FieldServer Computer Drive FS 8700 19 User Manual

A Sierra Monitor Company  
Driver Manual  
(Supplement to the FieldServer Instruction Manual)  
FS-8700-19 Metasys N2  
APPLICABILITY & EFFECTIVITY  
Effective for all systems manufactured after May 1, 2001  
Driver Version:  
1.02  
Document Revision: 22  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 3 of 51  
1.  
Metasys N2 Description  
TheꢀMetasysꢀN2ꢀnetworkꢀsupportsꢀcommunicationsꢀwithꢀaꢀdiverseꢀrangeꢀofꢀdevices.ꢀꢀManyꢀN2ꢀ  
compatibleꢀdevicesꢀuseꢀtheirꢀownꢀversionꢀofꢀtheꢀprotocolꢀandꢀcareꢀmustꢀbeꢀtakenꢀtoꢀensureꢀthatꢀ  
theꢀdeviceꢀofꢀinterestꢀisꢀcoveredꢀbyꢀtheꢀFieldServerꢀimplementation.ꢀ  
AtꢀpresentꢀtheꢀFieldServerꢀN2ꢀdriverꢀwillꢀsupportꢀcommunicationsꢀwithꢀtheꢀfollowingꢀdevicesꢀorꢀ  
deviceꢀclassesꢀwhenꢀactingꢀasꢀaꢀClient:ꢀ  
1.ꢀ N2Openꢁcompliantꢀ devices.ꢀ N2Openꢀ isꢀ aꢀ publishedꢀ N2ꢁcompatibleꢀ protocolꢀ enablingꢀ 3rdꢀ  
partyꢀdeviceꢀvendorsꢀtoꢀintegrateꢀwithꢀN2.ꢀ  
2.ꢀ VMA 1400ꢀseriesꢀ(withꢀrestrictions,ꢀasꢀdescribedꢀinꢀthisꢀdocument)ꢀ  
3.ꢀ DX9100ꢀandꢀXT9100ꢀ  
WhenꢀactingꢀasꢀaꢀServer,ꢀtheꢀFieldServerꢀN2ꢀdriverꢀcanꢀemulateꢀanꢀN2Openꢀdeviceꢀonly.ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 4 of 51  
2.  
Driver Scope of Supply  
2.1. Supplied by FieldServer Technologies for this driver  
FieldServer Technologies  
PART #  
Description  
FSꢁ8915ꢁ10ꢀ  
FSꢁ8915ꢁ10ꢀ  
FSꢁ8917ꢁ02ꢀ  
FSꢁ8917ꢁ01ꢀ  
UTPꢀcableꢀ(7ꢀfoot)ꢀforꢀEthernetꢀconnectionꢀ  
UTPꢀcableꢀ(7ꢀfoot)ꢀforꢀRSꢁ232ꢀuseꢀ  
RJ45ꢀtoꢀDB9Fꢀconnectorꢀadapterꢀ  
RJ45ꢀtoꢀDB25Mꢀconnectionꢀadapterꢀ  
RSꢁ485ꢀconnectionꢀadapterꢀ  
SPA59132ꢀ  
FSꢁ8700ꢁ19ꢀ  
DriverꢀManual.ꢀ  
2.2.  
2.2.1.  
Provided by the Supplier of 3rd Party Equipment  
Hardware  
PART #  
DESCRIPTION  
MetasysꢀNCUꢀorꢀotherꢀdeviceꢀ  
2.2.2.  
Required 3rd Party Software  
Dependingꢀonꢀapplication,ꢀJCIꢀsoftwareꢀmayꢀbeꢀnecessaryꢀ  
2.2.3.  
Required 3rd Party Configuration  
Dependingꢀonꢀapplication,ꢀthirdꢀpartyꢀdevicesꢀmayꢀneedꢀconfigurationꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 5 of 51  
3.  
Hardware Connections  
FieldServer as a Client  
N2ꢀbus  
3rdꢀPartyꢀ  
System  
FieldServer  
N2ꢀdevices  
FieldServer as a Server  
N2ꢀbus  
NCM,ꢀN30ꢀorꢀ  
otherꢀN2ꢀclient  
(408)ꢁ262ꢁ2299  
MetasysN2  
CONNECTION DIAGRAM  
3rdꢀPartyꢀ  
System  
FieldServer  
N2ꢀdevices  
BASE NAME:  
FILE NAME: FS-8700-19  
DATE: 05/31/06  
BY: MC  
3.1.  
Hardware Connection Tips / Hints  
WhenꢀusingꢀtheꢀFSꢁX40ꢀensureꢀthatꢀtheꢀFieldServerꢀisꢀconnectedꢀtoꢀtheꢀnetworkꢀusingꢀoneꢀ  
orꢀbothꢀofꢀtheꢀRSꢁ485ꢀportsꢀmarkedꢀR1ꢀandꢀR2.ꢀꢀIfꢀmoreꢀportsꢀareꢀrequired,ꢀP1ꢁP8ꢀmayꢀbeꢀ  
usedꢀinꢀconjunctionꢀwithꢀanꢀRSꢁ232ꢁtoꢁRSꢁ485ꢀconverter.ꢀ  
WhenꢀusingꢀtheꢀFSꢁX20,ꢀensureꢀthatꢀtheꢀserialꢀportꢀisꢀconfiguredꢀasꢀanꢀRSꢁ485ꢀport.ꢀReferꢀ  
toꢀAppendixꢀB.3ꢀforꢀmoreꢀinformation.ꢀ  
OnlyoneN2ClientmaybeconnectedtoaN2network.IftheFieldServeristoactasaꢀ  
Client,ꢀensureꢀthatꢀnoꢀotherꢀClientsꢀareꢀconnectedꢀtoꢀtheꢀsameꢀN2ꢀnetwork.ꢀꢀ  
Note: Interceptorꢀmodeꢀisꢀnoꢀlongerꢀsupportedꢀforꢀthisꢀdriver.  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 6 of 51  
4.  
Configuring the FieldServer as a Metasys N2 Client  
Forꢀ aꢀ detailedꢀ discussionꢀ onꢀ FieldServerꢀ configuration,ꢀ pleaseꢀ referꢀ toꢀ theꢀ FieldServerꢀ  
Configurationmanual.Theinformationthatfollowsdescribeshowtoexpanduponthefactoryꢀ  
defaultsꢀprovidedꢀinꢀtheꢀconfigurationꢀfilesꢀincludedꢀwithꢀtheꢀFieldServerꢀ(Seeꢀ“.csv”ꢀsampleꢀfilesꢀ  
providedꢀwithꢀtheꢀFieldServer).ꢀ  
ThisꢀsectionꢀdocumentsꢀandꢀdescribesꢀtheꢀparametersꢀnecessaryꢀforꢀconfiguringꢀtheꢀFieldServerꢀ  
toꢀcommunicateꢀwithꢀaꢀMetasysꢀN2ꢀServer.  
4.1.  
Data Arrays/Descriptors  
TheconfigurationfileꢀdefinesꢀtheꢀFieldServerꢀinterfaces,ꢀandꢀtheꢀdataꢀroutingꢀrequired.ꢀꢀInꢀ  
orderꢀ toꢀ enableꢀ theꢀ FieldServerꢀ forꢀ Metasysꢀ N2ꢀ communications,ꢀ theꢀ driverꢀ independentꢀ  
FieldServerꢀbuffersꢀneedꢀtoꢀbeꢀdeclaredꢀinꢀtheꢀ“DataꢀArrays”ꢀsection,ꢀtheꢀdestinationꢀdeviceꢀ  
addressesneedtobedeclaredintheClientSideNodes”section,andthedatarequiredꢀ  
fromꢀtheꢀServersꢀneedsꢀtoꢀbeꢀmappedꢀinꢀtheꢀ“ClientꢀSideꢀMapꢀDescriptors”ꢀsection.ꢀꢀ  
Noteꢀthatꢀinꢀtheꢀtables,ꢀ*ꢀindicatesꢀanꢀoptionalꢀparameter,ꢀwithꢀtheꢀboldꢀlegalꢀvalueꢀbeingꢀtheꢀ  
defaultvalue.ꢀWhereonlyonelegalvalueisgiven,noothervaluesforꢀthatꢀparameterꢀareꢀ  
allowed.ꢀ  
Section Title  
Data_Arraysꢀ  
Column Title  
Function  
Legal Values  
Upꢀtoꢀ15ꢀalphanumericꢀ  
charactersꢀ  
Data_Array_Nameꢀ  
ProvideꢀnameꢀforꢀDataꢀArrayꢀ  
Float,ꢀBit,ꢀUInt16,ꢀSInt16,ꢀ  
Provideꢀdataꢀformat.ꢀEachꢀDataꢀArrayꢀ Packed_Bit,ꢀByte,ꢀ  
Data_Array_Formatꢀ  
Data_Array_Lengthꢀ  
canꢀonlyꢀtakeꢀonꢀoneꢀformat.ꢀ  
Packed_Byte,ꢀ  
Swapped_Byteꢀ  
NumberꢀofꢀDataꢀObjects.ꢀMustꢀbeꢀ  
largerꢀthanꢀtheꢀdataꢀstorageꢀareaꢀ  
requiredꢀbyꢀtheꢀMapꢀDescriptorsꢀforꢀ  
theꢀdataꢀbeingꢀplacedꢀinꢀthisꢀarray.ꢀ  
1ꢁ10,000ꢀ  
Example  
//ꢀꢀꢀꢀDataꢀArraysꢀ  
Data_Arraysꢀ  
Data_Array_Name,ꢀ  
DA_AI_01,ꢀ  
DA_AO_01,ꢀ  
DA_DI_01,ꢀ  
DA_DO_01,ꢀ  
Data_Format,ꢀ  
UInt16,ꢀ  
UInt16,ꢀ  
Bit,ꢀ  
Data_Array_Lengthꢀ  
200ꢀ  
200ꢀ  
200ꢀ  
200  
Bit,ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 7 of 51  
4.2.  
Client Side Connection Descriptions  
Section Title  
Connectionsꢀ  
Column Title  
Function  
Specifyꢀwhichꢀportꢀtheꢀdeviceꢀisꢀ  
connectedꢀtoꢀtheꢀFieldServerꢀ  
Specifyꢀprotocolꢀusedꢀ  
Specifyꢀbaudꢀrateꢀ  
Legal Values  
P1ꢁP8,ꢀR1ꢁR21ꢀ  
Portꢀ  
Protocolꢀ  
Baud*ꢀ  
Metasys_N2ꢀ  
9600ꢀ  
Parity*ꢀ  
Data_Bits*ꢀ  
Specifyꢀparityꢀ  
Specifyꢀdataꢀbitsꢀ  
Noneꢀ  
8ꢀ  
Stop_Bits*ꢀ  
Specifyꢀstopꢀbitsꢀ  
1
Handshaking*ꢀ  
Pollꢀ_Delay*ꢀ  
Specifyꢀhardwareꢀhandshakingꢀ Noneꢀ  
Timeꢀbetweenꢀinternalꢀpollsꢀ  
DurationꢀofꢀRTSꢀassertꢀbeforeꢀ  
startꢀofꢀtransmissionꢀ  
0
Line_Drive_On*  
0.001s  
DurationꢀofꢀRTSꢀassertꢀafterꢀ  
endꢀofꢀtransmissionꢀ  
Line_Drive_Off*ꢀ  
0.000s  
Example  
//    ClientꢀSideꢀConnectionsꢀ  
Connectionsꢀ  
Port,ꢀ  
R1,ꢀ  
Protocolꢀ  
Metasys_N2ꢀ  
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀꢀꢀꢀꢀ  
1Notꢀallꢀportsꢀshownꢀareꢀnecessarilyꢀsupportedꢀbyꢀtheꢀhardware.ꢀConsultꢀtheꢀappropriateꢀInstructionꢀ  
manualꢀforꢀdetailsꢀofꢀtheꢀportsꢀavailableꢀonꢀspecificꢀhardware.  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 8 of 51  
4.3.  
Client Side Node Descriptors  
Section  
Title  
Nodesꢀ  
Column  
Title  
Function  
Legal Values  
Upꢀtoꢀ32ꢀ  
Node_Nameꢀ Provideꢀnameꢀforꢀnodeꢀ  
alphanumericꢀ  
charactersꢀ  
1ꢁ255ꢀ  
Node_IDꢀ  
Protocolꢀ  
StationꢀaddressꢀofꢀphysicalꢀServerꢀnodeꢀ  
Specifyꢀprotocolꢀusedꢀ  
Metasys_N2ꢀ  
Specifyꢀwhichꢀportꢀtheꢀdeviceꢀisꢀconnectedꢀtoꢀtheꢀ  
FieldServerꢀ  
Connectionꢀ  
P1ꢁP8,ꢀR1ꢁR21ꢀ  
Identifyꢀtypeꢀofꢀdeviceꢀ  
Ifꢀthisꢀparameterꢀisꢀomittedꢀtheꢀdriverꢀtreatsꢀtheꢀ  
configurationꢀasꢀaꢀN2Openꢀconfigurationꢀandꢀmarksꢀ  
theꢀNode_TypeꢀasꢀN2OpenClientꢀwhenꢀusingꢀRuinetꢀ N2OpenClient,ꢀ  
Node_Type  
toꢀcheckꢀtheꢀNodeꢀparameters.ꢀꢀ  
DX9100,ꢀVMA,ꢀ  
N2Openꢀ  
IfꢀtheꢀNode_TypeꢀisꢀspecifiedꢀasꢀN2Openꢀthenꢀtheꢀ  
driverꢀstillꢀactsꢀasꢀN2ꢀOpenꢀconfigurationꢀbutꢀsomeꢀ  
legacyꢀportꢀexpanderꢀfunctionalityꢀusedꢀinꢀsomeꢀ  
legacyꢀadvancedꢀconfigurationꢀisꢀenabled.  
Example  
//ꢀꢀꢀꢀClientꢀSideꢀNodesꢀ  
Nodesꢀ  
Node_Name,ꢀ  
PLCꢀ1,ꢀ  
Node_ID,ꢀ  
1,ꢀ  
Protocol,ꢀ  
Metasys_N2,ꢀ  
Connection,ꢀ  
P8,ꢀ  
Node_Typeꢀ  
VMAꢀ  
4.4.  
4.4.1.  
Client Side Map Descriptors  
FieldServer Related Map Descriptor Parameters  
Column Title  
Function  
NameꢀofꢀthisꢀMapꢀ  
Descriptorꢀ  
Legal Values  
Upꢀtoꢀ32ꢀalphanumericꢀ  
charactersꢀ  
Map_Descriptor_Nameꢀ  
NameꢀofꢀDataꢀArrayꢀ  
whereꢀdataꢀisꢀtoꢀbeꢀ  
OneꢀofꢀtheꢀDataꢀArrayꢀnamesꢀ  
fromꢀ“DataꢀArray”ꢀsectionꢀ  
Data_Array_Nameꢀ  
storedꢀinꢀtheꢀFieldServerꢀ aboveꢀ  
StartingꢀlocationꢀinꢀDataꢀ 0ꢀtoꢀmaximumꢀspecifiedꢀinꢀ  
Data_Array_Offsetꢀ  
Functionꢀ  
Arrayꢀ  
“DataꢀArray”ꢀsectionꢀaboveꢀ  
FunctionꢀofꢀClientꢀMapꢀ  
Descriptorꢀ  
RDBC,ꢀWRBC,ꢀWRBXꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 9 of 51  
4.4.2.  
Driver Related Map Descriptor Parameters  
4.4.2.1.  
Column Title  
N2Open Map Descriptor Parameters  
Function  
Legal Values  
Oneꢀofꢀtheꢀnodeꢀnamesꢀ  
NameꢀofꢀNodeꢀtoꢀfetchꢀdataꢀfromꢀ specifiedꢀinꢀ“ClientꢀNodeꢀ  
Descriptor”ꢀaboveꢀ  
Node_Nameꢀ  
Data_Typeꢀ  
Ifꢀtheꢀvendorꢀdeviceꢀlistsꢀaꢀ  
pointꢀasꢀBDꢀthenꢀuseꢀ  
Data_Type=Byte.ꢀ  
Ifꢀtheꢀvendorꢀdeviceꢀlistsꢀaꢀ  
pointꢀasꢀADIꢀthenꢀuseꢀ  
Data_Type=Integer.ꢀ  
Dataꢀtypeꢀ  
Ifꢀtheꢀvendorꢀdeviceꢀlistsꢀaꢀ  
pointꢀasꢀADFꢀthenꢀuseꢀ  
Data_Type=Float_Reg.ꢀ  
AI,ꢀAO,ꢀDI,ꢀDO,ꢀ  
Float_Reg,ꢀInteger,ꢀByteꢀ  
Lengthꢀ  
LengthꢀofꢀMapꢀDescriptorꢀ  
1ꢀ  
Addressꢀ  
Startingꢀaddressꢀofꢀreadꢀblockꢀ  
1ꢁ256ꢀ  
UsedꢀtoꢀspecifyꢀanꢀN2ꢁspecificꢀ  
MN2_Function*ꢀ function,ꢀe.g.ꢀCOS.ꢀSeeꢀ  
descriptionꢀbelow.ꢀ  
COS,ꢀOverride,ꢀReleaseꢀ  
Usedꢀtoꢀspecifyꢀtheꢀattributeꢀifꢀanꢀ  
See  
attributeꢀotherꢀthanꢀCurrentꢀValueꢀ  
isꢀtoꢀbeꢀaccessed.ꢀSeeꢀattributeꢀ  
tableꢀbelowꢀ  
MN2_Attribute*ꢀ  
N2Open Attribute Tableꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Data Type  
Page 10 of 51  
N2Open Attribute Table  
Attribute No.  
Attribute  
ObjectꢀConfigurationꢀ  
1
2
3ꢀ  
4
5
6
7
8
1
2
1
2
3
1
2
3
4
5
1
2
1
2
1
2
ObjectꢀStatusꢀ  
Analog Input Value  
LowꢀAlarmꢀLimitꢀ  
HighꢀAlarmꢀLimitꢀ  
LowꢀWarnꢀLimitꢀ  
HighꢀWarnꢀLimitꢀ  
Differentialꢀ  
ObjectꢀConfigurationꢀ  
ObjectꢀStatusꢀ  
ObjectꢀConfigurationꢀ  
ObjectꢀStatusꢀ  
Analog Input  
BinaryꢀInputꢀ  
Analog Output  
CurrentꢀValueꢀ  
ObjectꢀConfigurationꢀ  
ObjectꢀStatusꢀ  
MinimumꢀOnꢁTimeꢀ  
MinimumꢀOffꢁTimeꢀ  
MaximumꢀCycles/Hourꢀ  
ObjectꢀStatusꢀ  
Binary Output  
Internal Float  
Internal Integer  
Internal Byte  
CurrentꢀValueꢀ  
ObjectꢀStatusꢀ  
CurrentꢀValueꢀ  
ObjectꢀStatusꢀ  
CurrentꢀValueꢀ  
Using Change of State (COS) – N2Open  
Ifꢀ aꢀ largeꢀ numberꢀ ofꢀ pointsꢀ aretoꢀ beꢀ monitored,ꢀ optimalꢀ efficiencyꢀ isꢀ achievedꢀ byꢀ  
usingꢀ theꢀ COSꢀ mechanismꢀ insteadꢀ ofꢀ readingꢀ eachꢀ individualꢀ pointꢀ directly.ꢀ ꢀ Aꢀ  
N2OpenꢀdeviceꢀrespondsꢀtoꢀaꢀCOSꢀpollꢀwithꢀaꢀchangeꢀrecordꢀifꢀaꢀchangeꢀhasꢀtakenꢀ  
place.ꢀꢀOnꢀstartupꢀtheꢀdeviceꢀwillꢀreportꢀtheꢀstateꢀofꢀallꢀitsꢀpointsꢀwhenꢀitꢀreceivesꢀaꢀ  
COSꢀpoll.ꢀ  
TwokindsofMapDescriptorsarerequiredforeverynodethatistobemonitoredꢀ  
usingꢀCOS:ꢀ  
AꢀCOSꢀpollingꢀMapꢀDescriptorꢀwithꢀFunctionꢀsetꢀtoꢀCOS_Poll.ꢀ  
ACOS_Read(i.e.FunctionsettoCOS_Read)MapDescriptorforꢀeverypointꢀ  
onꢀthatꢀnodeꢀthatꢀisꢀtoꢀbeꢀmonitored.ꢀꢀAnyꢀCOSꢀrecordsꢀreceivedꢀwillꢀbeꢀstoredꢀtoꢀ  
theꢀmatchingꢀMapꢀDescriptorꢀdataꢀlocation.ꢀ  
NoteꢀthatꢀtheꢀCOS_ReadꢀMapꢀDescriptorꢀhasꢀanꢀoptionalꢀscan_interval.ꢀꢀIfꢀaꢀvalueꢀisꢀ  
setꢀtheꢀMapꢀDescriptorꢀwillꢀpollꢀatꢀthatꢀrateꢀinꢀadditionꢀtoꢀreceivingꢀCOSꢀdata.ꢀꢀThisꢀ  
canꢀbeꢀusedꢀifꢀtheꢀvaluesꢀareꢀtoꢀbeꢀrefreshedꢀcontinuallyꢀevenꢀifꢀtheyꢀdon’tꢀchange.ꢀꢀIfꢀ  
theꢀ scan_intervalꢀ isꢀ notconfigured(throughꢀ omittingꢀ theꢀ column,ꢀ orꢀ byꢀ settingtheꢀ  
valueꢀtoꢀ‘ꢁ‘)ꢀtheꢀCOS_ReadꢀMapꢀDescriptorꢀwillꢀnotꢀcauseꢀactiveꢀpollsꢀonceꢀtheꢀvalueꢀ  
hasꢀbeenꢀinitialized.ꢀꢀSeeꢀ4.4.4ꢀforꢀexample.ꢀ  
Important Note on COS Operation in N2Open  
Pleaseꢀ beꢀ awareꢀ thatꢀ N2Openꢀ devicesꢀ willꢀ onlyꢀ reportꢀ valueꢀ changesꢀ underꢀ theꢀ  
followingꢀconditions:ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 11 of 51  
Point Type  
AI  
Conditions that will trigger a COS report  
pointꢀstatusꢀchangeꢀ(e.g.ꢀoverride)ꢀ  
changeꢀinꢀalarmꢀorꢀwarningꢀstatusꢀ  
NB: no value changes within the normal band are reported by COS!  
pointꢀstatusꢀchangeꢀ(e.g.ꢀoverride)ꢀ  
NB: no value changes within the normal band are reported by COS!ꢀ  
AO  
BI, BO  
pointꢀstatusꢀchangeꢀ(e.g.ꢀoverride);ꢀincludesꢀcurrentꢀvalueꢀ(On/Off)ꢀ  
ADI, ADF, BD none;ꢀCOSꢀcannotꢀbeꢀusedꢀwithꢀinternalꢀdataꢀtypes.ꢀ  
Using Override and Release – N2Open  
Itꢀ isꢀ notꢀ normallyꢀ necessaryꢀ toꢀ useꢀ theꢀ Overrideꢀ commandꢀ explicitlyꢀ asꢀ theꢀ  
FieldServerꢀautomaticallyꢀusesꢀthisꢀcommandꢀwhenꢀtheꢀCurrentꢀValueꢀattributeꢀofꢀaꢀ  
pointꢀisꢀwritten.ꢀꢀForꢀanyꢀotherꢀattributeꢀitꢀusesꢀtheꢀWriteꢀcommand.ꢀꢀItꢀwillꢀsometimesꢀ  
benecessarytosendaReleasecommandtoꢀanꢀoverriddenꢀpoint,ꢀhowever.ꢀToꢀdoꢀ  
this,ꢀ aꢀ Mapꢀ Descriptorꢀ mustꢀ beꢀ configuredꢀ withꢀ Functionꢀ setꢀ toꢀ wrbxꢀ andꢀ  
MN2_Function setꢀ toꢀ Release.ꢀ ꢀ Then,ꢀ whenꢀ anyꢀ valueꢀ isꢀ storedꢀ toꢀ theꢀ Mapꢀ  
Descriptorꢀ dataꢀ location,ꢀ theꢀ Releaseꢀ commandꢀ willꢀ beꢀ sentꢀ toꢀ theꢀ N2Openꢀ pointꢀ  
specifiedꢀbyꢀtheꢀMapꢀDescriptor.ꢀ  
4.4.2.2.  
VMA Map Descriptor Parameters  
Column Title  
Function  
Legal Values  
Oneꢀofꢀtheꢀnodeꢀnamesꢀ  
specifiedꢀinꢀ“ClientꢀNodeꢀ  
Descriptor”ꢀaboveꢀ  
AI,ꢀAO,ꢀDI,ꢀDO,ꢀDriverꢀ  
(usedꢀforꢀADF,ꢀADIꢀandꢀ  
BD)ꢀ  
NameꢀofꢀNodeꢀtoꢀfetchꢀ  
dataꢀfromꢀ  
Node_Nameꢀ  
Data_Typeꢀ  
Dataꢀtypeꢀ  
Lengthꢀ  
LengthꢀofꢀMapꢀDescriptorꢀ 1ꢀ  
Startingꢀaddressꢀofꢀreadꢀ  
blockꢀ  
Addressꢀ  
1ꢁ256ꢀ  
Dataꢀtypeꢀspecifierꢀtoꢀbeꢀ  
setꢀwhenꢀData_Typeꢀhasꢀ  
beenꢀsetꢀtoꢀDriverꢀ  
MN2_Typeꢀ  
5ꢁ7ꢀ  
ADI, ADF and BD types: using the “Driver” Data_Type and MN2_Type fieldsꢀ  
TheVMAprotocolusesabytevaluetospecifythedatatypes.ꢀTheꢀstandardꢀtypesꢀ  
AI,ꢀAO,ꢀDIꢀandꢀDOꢀcorrespondꢀtoꢀaꢀbyteꢀvalueꢀofꢀ1ꢀthroughꢀ4ꢀrespectively.ꢀꢀTheꢀtypesꢀ  
ADF,ꢀ ADIꢀ andꢀ BDꢀ areꢀ believedꢀ toꢀ correspondꢀ toꢀ aꢀ byteꢀ valueꢀ ofꢀ 5ꢀ throughꢀ 7ꢀ  
respectively.ꢀIfꢀtheꢀuserꢀwishesꢀtoꢀuseꢀanyꢀotherꢀtypeꢀvalueꢀbasedꢀonꢀknowledgeꢀofꢀaꢀ  
particularVMAconfiguration,thenthatvaluemayalsobespecifiedhere.Refertoꢀ  
Sectionꢀ4.4.5ꢀforꢀaꢀspecificꢀexample.ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 12 of 51  
Driver Data_Type  
MN2_Type values  
Point Type  
AIꢀ  
AOꢀ  
BIꢀ  
Known Value2  
Suggested Value3  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
BOꢀ  
ADFꢀ  
ADIꢀ  
BDꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
Ifꢀ aꢀ largeꢀ numberꢀ ofꢀ pointsꢀ aretoꢀ beꢀ monitored,ꢀ optimalꢀ efficiencyꢀ isꢀ achievedꢀ byꢀ  
usingꢀ theꢀ COSꢀ mechanismꢀ insteadꢀ ofꢀ readingꢀ eachꢀ individualꢀ pointꢀ directly.ꢀ ꢀ Anꢀ  
N2OpenꢀdeviceꢀrespondsꢀtoꢀaꢀCOSꢀpollꢀwithꢀaꢀchangeꢀrecordꢀifꢀaꢀchangeꢀhasꢀtakenꢀ  
place.ꢀꢀOnꢀstartupꢀtheꢀdeviceꢀwillꢀreportꢀtheꢀstateꢀofꢀallꢀitsꢀpointsꢀwhenꢀitꢀreceivesꢀaꢀ  
COSꢀpoll.ꢀ  
ThreeꢀkindsꢀofꢀMapꢀDescriptorsꢀareꢀrequiredꢀforꢀeveryꢀnodeꢀthatꢀisꢀtoꢀbeꢀmonitoredꢀ  
usingꢀCOS:ꢀ  
ꢀ Aꢀ COSꢀ initializationꢀ Mapꢀ Descriptorꢀ withꢀ Functionꢀ setꢀ toꢀ ARSꢀ andꢀ  
MN2_FunctionꢀsetꢀtoꢀCOS_Enable.ꢀꢀThisꢀMapꢀDescriptorꢀenablesꢀCOSꢀpollingꢀ  
ofꢀthoseꢀpointsꢀonꢀtheꢀVMAꢀforꢀwhichꢀPassiveꢀMapꢀDescriptorsꢀexist.ꢀ  
ꢀ AꢀCOSꢀpollingꢀMapꢀDescriptorꢀwithꢀFunctionꢀsetꢀtoꢀrdbcꢀandꢀMN2_Functionꢀsetꢀ  
toꢀCOS.ꢀ  
ꢀ AꢀPassiveꢀ(i.e.ꢀFunctionꢀsetꢀtoꢀPassive)ꢀMapꢀDescriptorꢀforꢀeveryꢀpointꢀonꢀthatꢀ  
nodethatistobemonitored.AnyCOSrecordsreceivedwillbestoredtotheꢀ  
matchingꢀMapꢀDescriptorꢀdataꢀlocation.ꢀ  
SeeꢀexampleꢀinꢀSectionꢀ4.4.5ꢀ  
Using Override and Release - VMAꢀ  
Itꢀ isꢀ normallyꢀ notꢀ necessaryꢀ toꢀ useꢀ theꢀ Overrideꢀ commandꢀ explicitlyꢀ asꢀ theꢀ  
FieldServerꢀautomaticallyꢀusesꢀthisꢀcommandꢀwhenꢀtheꢀCurrentꢀValueꢀattributeꢀofꢀaꢀ  
pointꢀisꢀwritten.ꢀꢀForꢀanyꢀotherꢀattributeꢀitꢀusesꢀtheꢀWriteꢀcommand.ꢀꢀItꢀwillꢀsometimesꢀ  
benecessarytosendaReleasecommandtoꢀanꢀoverriddenꢀpoint,ꢀhowever.ꢀToꢀdoꢀ  
this,ꢀ aꢀ Mapꢀ Descriptorꢀ mustꢀ beꢀ configuredꢀ withꢀ Functionꢀ setꢀ toꢀ wrbxꢀ andꢀ  
MN2_Function setꢀ toꢀ Release.ꢀ ꢀ Then,ꢀ whenꢀ anyꢀ valueꢀ isꢀ storedꢀ toꢀ theꢀ Mapꢀ  
Descriptorꢀ dataꢀ location,ꢀ theꢀ Releaseꢀ commandꢀ willꢀ beꢀ sentꢀ toꢀ theꢀ VMAꢀ pointꢀ  
specifiedꢀbyꢀtheꢀMapꢀDescriptor.ꢀ  
Note:TheVMAReleasefunctiononlyworksforanalogandbinaryinputs(AIandꢀ  
BI).ꢀꢀOutputsꢀmayꢀbeꢀrestoredꢀtoꢀtheirꢀoriginalꢀvalueꢀusingꢀanꢀexplicitꢀwriteꢀcommand.ꢀ  
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀꢀꢀꢀꢀ  
2Forꢀinformationꢀonly.ꢀDoꢀnotꢀuseꢀDriverꢀtypeꢀforꢀthese,ꢀbutꢀspecifyꢀAI,ꢀAO,ꢀBIꢀorꢀBOꢀdirectlyꢀinꢀtheꢀData_Typeꢀfield.ꢀ  
3Theseꢀvaluesꢀareꢀbelievedꢀtoꢀbeꢀcorrectꢀforꢀtheꢀcorrespondingꢀpointꢀtypes,ꢀbutꢀnoꢀguaranteeꢀcanꢀbeꢀgivenꢀatꢀthisꢀtime.ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 13 of 51  
4.4.2.3.  
DX9100 Map Descriptor Parameters  
Column Title  
Function  
Legal Values  
Oneꢀofꢀtheꢀnodeꢀnamesꢀ  
specifiedꢀinꢀ“ClientꢀNodeꢀ  
Descriptor”ꢀaboveꢀ  
NameꢀofꢀNodeꢀtoꢀfetchꢀ  
dataꢀfromꢀ  
Node_Nameꢀ  
Lengthꢀ  
LengthꢀofꢀMapꢀDescriptorꢀ 1ꢀ  
Startingꢀaddressꢀofꢀreadꢀ  
blockꢀ  
Addressꢀ  
0ꢀꢁꢀ2397ꢀ  
ForDX9100addressespleaserefertotheDX9100userdocumentation.Thislistsꢀ  
theꢀname,ꢀfunctionꢀ(read/write)ꢀandꢀdataꢀformatꢀofꢀallꢀavailableꢀpoints.ꢀAlternatively,ꢀ  
obtainꢀassistanceꢀfromꢀFieldServerꢀTechnicalꢀSupport.ꢀ  
4.4.3.  
Column Title  
Scan_Intervalꢀ  
Timing Parameters  
Function  
Legal Values  
Rateꢀatꢀwhichꢀdataꢀisꢀpolledꢀ ≥0.001sꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
 
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 16 of 51  
5.  
Configuring the FieldServer as a Metasys N2 Server  
Forꢀ aꢀ detailedꢀ discussionꢀ onꢀ FieldServerꢀ configuration,ꢀ pleaseꢀ referꢀ toꢀ theꢀ FieldServerꢀ  
ConfigurationManual.ꢀTheꢀinformationꢀthatꢀfollowsꢀdescribesꢀhowꢀtoꢀexpandꢀuponꢀtheꢀfactoryꢀ  
defaultsꢀprovidedꢀinꢀtheꢀconfigurationꢀfilesꢀincludedꢀwithꢀtheꢀFieldServerꢀ(Seeꢀ“.csv”ꢀfilesꢀonꢀtheꢀ  
driverꢀdiskette).ꢀ  
ThisꢀsectionꢀdocumentsꢀandꢀdescribesꢀtheꢀparametersꢀnecessaryꢀforꢀconfiguringꢀtheꢀFieldServerꢀ  
toꢀcommunicateꢀwithꢀaꢀMetasysꢀN2OpenꢀClient.ꢀꢀNote that only the N2Open variation of the  
N2 protocol may be used when configuring the FieldServer as a Server.  
TheꢀconfigurationꢀfileꢀtellsꢀtheꢀFieldServerꢀaboutꢀitsꢀinterfaces,ꢀandꢀtheꢀroutingꢀofꢀdataꢀrequired.ꢀ  
Inꢀ orderꢀ toꢀ enableꢀ theꢀ FieldServerꢀ forꢀ Metasysꢀ N2ꢀ communications,ꢀ theꢀ driverꢀ independentꢀ  
FieldServerꢀ buffersꢀ needꢀ toꢀ beꢀ declaredꢀ inꢀ theꢀ “Dataꢀ Arrays”ꢀ section,ꢀ theꢀ FieldServerꢀ virtualꢀ  
node(s)ꢀneedsꢀtoꢀbeꢀdeclaredꢀinꢀtheꢀ“ServerꢀSideꢀNodes”ꢀsection,ꢀandꢀtheꢀdataꢀtoꢀbeꢀprovidedꢀtoꢀ  
theꢀClientsꢀneedsꢀtoꢀbeꢀmappedꢀinꢀtheꢀ“ServerꢀSideꢀMapꢀDescriptors”ꢀsection.ꢀDetailsꢀonꢀhowꢀtoꢀ  
doꢀthisꢀcanꢀbeꢀfoundꢀbelow.ꢀ  
Notethatinthetables,*indicatesanoptionalparameter,withtheboldlegalvaluebeingtheꢀ  
default.ꢀ  
5.1.  
Server Side Connection Descriptors  
Section Title  
Connectionsꢀ  
Column Title  
Portꢀ  
Function  
Specifyꢀwhichꢀportꢀtheꢀdeviceꢀisꢀ  
connectedꢀtoꢀtheꢀFieldServerꢀ  
Specifyꢀprotocolꢀusedꢀ  
Specifyꢀbaudꢀrateꢀ  
Legal Values  
P1ꢁP8,ꢀR1ꢁR24ꢀ  
Protocolꢀ  
Baud*ꢀ  
Metasys_N2ꢀ  
9600ꢀ  
Parity*ꢀ  
Data_Bits*ꢀ  
Specifyꢀparityꢀ  
Specifyꢀdataꢀbitsꢀ  
Noneꢀ  
8ꢀ  
Stop_Bits*ꢀ  
Specifyꢀstopꢀbitsꢀ  
1
Handshaking*ꢀ  
Pollꢀ_Delay*ꢀ  
Specifyꢀhardwareꢀhandshakingꢀ Noneꢀ  
Timeꢀbetweenꢀinternalꢀpollsꢀ  
DurationꢀofꢀRTSꢀassertꢀbeforeꢀ  
startꢀofꢀtransmissionꢀ  
0
Line_Drive_On*  
0.001s  
DurationꢀofꢀRTSꢀassertꢀafterꢀ  
endꢀofꢀtransmissionꢀ  
Line_Drive_Off*ꢀ  
0.000s  
Example  
//    ServerꢀSideꢀConnectionsꢀ  
Connectionsꢀ  
Port,ꢀ  
P8,ꢀ  
Protocolꢀ  
Metasys_N2ꢀ  
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀꢀꢀꢀꢀ  
4Notꢀallꢀportsꢀshownꢀareꢀnecessarilyꢀsupportedꢀbyꢀtheꢀhardware.ꢀConsultꢀtheꢀappropriateꢀInstructionꢀ  
manualꢀforꢀdetailsꢀofꢀtheꢀportsꢀavailableꢀonꢀspecificꢀhardware.  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 17 of 51  
Legal Values  
5.2.  
Server Side Node Descriptors  
Section Title  
Nodesꢀ  
Column Title  
Function  
Upꢀtoꢀ32ꢀ  
Node_Nameꢀ  
Provideꢀnameꢀforꢀnodeꢀ  
alphanumericꢀ  
charactersꢀ  
MetasysN2ꢀstationꢀaddressꢀofꢀphysicalꢀ  
Serverꢀnodeꢀ  
Specifyꢀprotocolꢀusedꢀ  
Node_IDꢀ  
Protocolꢀ  
1ꢁ255ꢀ  
Metasys_N2ꢀ  
SpecifiesꢀtimeꢀFieldServerꢀwillꢀreserveꢀ  
Server_Hold_Timeout*ꢀ Serverꢀsideꢀconnectionꢀwhileꢀwaitingꢀforꢀtheꢀ <ꢀ0.175s5ꢀ  
ClientꢀsideꢀtoꢀupdateꢀdataꢀinꢀData_Arrayꢀꢀ  
Identifyꢀtypeꢀofꢀdeviceꢀ  
Thisꢀparameterꢀneedꢀnotꢀbeꢀspecified.ꢀꢀTheꢀ  
N2OpenServer,  
Node_Type*  
Serverꢀsideꢀofꢀtheꢀdriverꢀcanꢀonlyꢀoperateꢀ  
asꢀanꢀN2ꢀServerꢀandꢀtheꢀoptionꢀforꢀsettingꢀitꢀ  
toꢀN2Openꢀisꢀpurelyꢀforꢀbackwardꢀ  
compatibility.ꢀ  
N2Open  
Example  
//ꢀꢀꢀꢀServerꢀSideꢀNodesꢀ  
Nodesꢀ  
Node_Name,ꢀ  
PLCꢀ1,ꢀ  
Node_ID,ꢀ  
1,ꢀ  
Protocolꢀ  
Metasys_N2ꢀ  
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ꢀꢀꢀꢀꢀꢀꢀ  
5Canꢀbeꢀsetꢀtoꢀ>0.175sꢀifꢀtheꢀClientꢀhasꢀbeeꢀsetꢀtoꢀtimeoutꢀafterꢀ>200ms.ꢀꢀReferꢀtoꢀAppendixꢀEꢀforꢀmoreꢀ  
information.  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 18 of 51  
5.3.  
5.3.1.  
Server Side Map Descriptors  
FieldServer Specific Map Descriptor Parameters  
Column Title  
Function  
NameꢀofꢀthisꢀMapꢀ  
Descriptorꢀ  
Legal Values  
Upꢀtoꢀ32ꢀalphanumericꢀ  
charactersꢀ  
Map_Descriptor_Nameꢀ  
NameꢀofꢀDataꢀArrayꢀwhereꢀ OneꢀofꢀtheꢀDataꢀArrayꢀ  
Data_Array_Nameꢀ  
dataꢀisꢀtoꢀbeꢀstoredꢀinꢀtheꢀ  
FieldServerꢀ  
namesꢀfromꢀ“DataꢀArray”ꢀ  
sectionꢀaboveꢀ  
StartingꢀlocationꢀinꢀDataꢀ  
Arrayꢀ  
FunctionꢀofꢀServerꢀMapꢀ  
Descriptorꢀ  
0ꢀtoꢀmaximumꢀspecifiedꢀinꢀ  
“DataꢀArray”ꢀsectionꢀaboveꢀ  
Data_Array_Offsetꢀ  
Functionꢀ  
Serverꢀ  
5.3.2.  
Column  
Driver Specific Map Descriptor Parameters  
Function  
Legal Values  
Title  
NameꢀofꢀNodeꢀtoꢀ  
fetchꢀdataꢀfromꢀ  
Oneꢀofꢀtheꢀnodeꢀnamesꢀspecifiedꢀinꢀ“Clientꢀ  
NodeꢀDescriptor”ꢀaboveꢀ  
Node_Nameꢀ  
IfꢀtheꢀvendorꢀdeviceꢀlistsꢀaꢀpointꢀasꢀBDꢀthenꢀ  
useꢀData_Type=Byte.ꢀ  
IfꢀtheꢀvendorꢀdeviceꢀlistsꢀaꢀpointꢀasꢀADIꢀthenꢀ  
useꢀData_Type=Integer.ꢀ  
Data_Typeꢀ  
Dataꢀtypeꢀ  
IfꢀtheꢀvendorꢀdeviceꢀlistsꢀaꢀpointꢀasꢀADFꢀthenꢀ  
useꢀData_Type=Float_Reg.ꢀ  
AI,ꢀAO,ꢀDI,ꢀDO,ꢀFloat_Reg,ꢀInteger,ꢀByteꢀ  
LengthꢀofꢀMapꢀ  
Descriptorꢀ  
Lengthꢀ  
1ꢀꢁꢀ256ꢀ  
Startingꢀaddressꢀofꢀ  
readꢀblockꢀ  
Addressꢀ  
1ꢀꢁꢀ256ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
 
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 21 of 51  
Appendix A.2. Managing Analog Inputs and Outputs for DX9100.  
RelativeꢀoffsetꢀforꢀviewingꢀanꢀAIꢀisꢀ7ꢀ  
RelativeꢀoffsetꢀforꢀviewingꢀandꢀforcingꢀanꢀAOꢀisꢀ6ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 22 of 51  
Appendix B. Troubleshooting tips  
Appendix B.1. Connection Tips & Hints  
WhenusingtheFieldServerasanN2 Client,makeverysurethatitisthe only Client /  
masterꢀ onꢀ theꢀ N2ꢀ network.ꢀ ꢀ Ifꢀ thereꢀ isꢀ anotherꢀ Clientꢀ onꢀ theꢀ networkꢀ thereꢀ willꢀ beꢀ  
communicationꢀconflicts.ꢀꢀTheseꢀwillꢀbeꢀreflectedꢀonꢀtheꢀFieldServerꢀasꢀprotocolꢀerrors.ꢀ  
Appendix B.2. Offline Behavior  
WhenꢀtheꢀClientꢀnodeꢀonꢀtheꢀFieldServerꢀgoesꢀoffline,ꢀtheꢀcorrespondingꢀdataꢀobjectsꢀonꢀtheꢀ  
FieldServerꢀ areꢀ alsoꢀ markedꢀ offline.ꢀ ꢀ Ifꢀ aꢀ clientꢀ pollsꢀ aꢀ virtualꢀ FieldServerꢀ nodeꢀ forꢀ thisꢀ  
particularꢀdata,ꢀtherefore,ꢀanꢀofflineꢀresponseꢀwillꢀbeꢀreturnedꢀbyꢀtheꢀFieldServer.ꢀꢀAꢀrequestꢀ  
fromꢀanꢀmasterꢀdeviceꢀforꢀaꢀFieldServerꢀtoꢀidentifyꢀitselfꢀwouldꢀbeꢀmetꢀbyꢀaꢀvalidꢀresponse,ꢀ  
however.Thiscouldleadtoconfusionandstatustoggling.ꢀThisꢀcanꢀbeꢀaddressedꢀusingꢀ  
Responsibleꢀ Mapꢀ Descriptorsꢀ andꢀ byꢀ configuringꢀ theꢀ virtualꢀ FieldServerꢀ usingꢀ theꢀ  
Offline_Methodꢀoption.ꢀꢀPleaseꢀreferꢀtoꢀtheꢀConfigurationꢀManualꢀforꢀfurtherꢀinformation.  
Appendix B.3. Tip on Overrides  
Itisimportantthattherebeonlyonedevice(includingtheslavedeviceitself)updatingaꢀ  
pointꢀwhichꢀisꢀinꢀoverriddenꢀmode.ꢀꢀTheꢀreasonꢀforꢀthisꢀisꢀthatꢀtheꢀvalueꢀofꢀtheꢀpointꢀcouldꢀbeꢀ  
changedbyanupdatefromanonꢁMetasysServerbeforetheoverrideisreleasedbytheꢀ  
MetasysꢀMaster.ꢀꢀInꢀthisꢀcase,ꢀtheꢀFieldServerꢀwouldꢀrespondꢀtoꢀaꢀpollꢀfromꢀtheꢀMasterꢀwithꢀ  
thisꢀchangedꢀdata.ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 23 of 51  
Appendix C. Setting up FS-B20 for RS-485  
Appendix C.1. Jumper Settings:  
Jumpersjp16,jp17,andjp18needtobetransferredfrompins1ꢁ2topins2ꢁ3inordertoꢀ  
enableꢀRSꢁ485.ꢀꢀTheseꢀjumpersꢀcanꢀbeꢀfoundꢀjustꢀbehindꢀtheꢀRJ45ꢀportsꢀinsideꢀtheꢀboxꢀꢀ  
Jmprꢀ18ꢀinꢀ485ꢀposition.ꢀ  
Jmprꢀ16ꢀinꢀ485ꢀposition.ꢀ  
Jmprꢀ17ꢀinꢀ485ꢀposition.ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 24 of 51  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 25 of 51  
Appendix C.2. Hardware connections  
TheꢀFSꢁ8917ꢁ16ꢀpigtailꢀcableꢀisꢀtypicallyꢀusedꢀforꢀthisꢀportꢀarrangement.ꢀꢀConnectionꢀisꢀ  
depictedꢀinꢀtheꢀfollowingꢀdiagram.ꢀ  
SERIAL  
FSꢁX20  
RJ45ꢀMaleꢀModularꢀ  
Jack  
ORANGE/WHITEꢀ  
(RJ45ꢁ08)  
BROWNꢀ  
(RJ45ꢁ01)  
FSꢁ8917ꢁ16  
+
G
BLUE/WHITEꢀ  
(RJ45ꢁ04)  
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
RJ45ꢀMaleꢀModularꢀJack  
RJ45ꢀFemaleꢀModularꢀJack  
Appendix C.3. Configuration Settings  
ꢀ TheꢀPortꢀaddressꢀinꢀtheꢀConfigurationꢀneedsꢀtoꢀbeꢀsetꢀtoꢀR1ꢀinsteadꢀofꢀP1.ꢀ  
ꢀ Line_Drive_OnꢀandꢀLine_Drive_Offꢀneedꢀtoꢀbeꢀdefinedꢀinꢀtheꢀconnectionsꢀsectionꢀofꢀtheꢀ  
configurationꢀfile.ꢀꢀTheseꢀneedꢀtoꢀbeꢀsetꢀtoꢀatꢀleastꢀ0.001s.ꢀꢀReferꢀtoꢀSectionsꢀ4.2ꢀandꢀ5.1ꢀ  
forꢀmoreꢀinformation.ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Appendix D. Memory Maps  
Page 26 of 51  
Appendix D.1. Metasys DX9100 Memory Map  
Programmable modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
9ꢀ  
64ꢀ ꢀ0040Hꢀꢀ  
160ꢀ ꢀ00A0Hꢀꢀ  
256ꢀ ꢀ0100Hꢀꢀ  
352ꢀ ꢀ0160Hꢀꢀ  
448ꢀ ꢀ01C0Hꢀꢀ  
544ꢀ ꢀ0220Hꢀꢀ  
640ꢀ ꢀ0280Hꢀꢀ  
736ꢀ ꢀ02E0Hꢀꢀ  
832ꢀ ꢀ0340Hꢀꢀ  
928ꢀ ꢀ03A0Hꢀꢀ  
1024ꢀ ꢀ0400Hꢀꢀ  
1120ꢀ ꢀ0460Hꢀꢀ  
10ꢀ  
11ꢀ  
12ꢀ  
Analog input modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
1216ꢀ ꢀ04C0Hꢀꢀ  
1232ꢀ ꢀ04D0Hꢀꢀ  
1248ꢀ ꢀ04E0Hꢀꢀ  
1264ꢀ ꢀ04F0Hꢀꢀ  
1280ꢀ ꢀ0500Hꢀꢀ  
1296ꢀ ꢀ0510Hꢀꢀ  
1312ꢀ ꢀ0520Hꢀꢀ  
1328ꢀ ꢀ0530Hꢀꢀ  
Analog output modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Versionꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
1344ꢀ ꢀ0540Hꢀꢀ  
1360ꢀ ꢀ0550Hꢀꢀ  
2ꢀ orꢀꢀlaterꢀ(newꢀforꢀversionꢀ6.0):ꢀ  
9ꢀ  
10ꢀ  
11ꢀ  
12ꢀ  
13ꢀ  
14ꢀ  
2304ꢀ ꢀ0900Hꢀꢀ  
2320ꢀ ꢀ0910Hꢀꢀ  
2336ꢀ ꢀ0920Hꢀꢀ  
2352ꢀ ꢀ0930Hꢀꢀ  
2368ꢀ ꢀ0940Hꢀꢀ  
2384ꢀ ꢀ0950Hꢀꢀ  
Digital output modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
1376ꢀ ꢀ0560Hꢀꢀ  
1392ꢀ ꢀ0570Hꢀꢀ  
1408ꢀ ꢀ0580Hꢀꢀ  
1424ꢀ ꢀ0590Hꢀꢀ  
1440ꢀ ꢀ05A0Hꢀꢀ  
1456ꢀ ꢀ05B0Hꢀꢀ  
Extension modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
1472ꢀ ꢀ05C0Hꢀꢀ  
1552ꢀ ꢀ0610Hꢀꢀ  
1632ꢀ ꢀ0660Hꢀꢀ  
1712ꢀ ꢀ06B0Hꢀꢀ  
1792ꢀ ꢀ0700Hꢀꢀ  
1872ꢀ ꢀ0750Hꢀꢀ  
1952ꢀ ꢀ07A0Hꢀꢀ  
2032ꢀ ꢀ07F0Hꢀꢀ  
Time schedule modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
2112ꢀ ꢀ0840Hꢀꢀ  
2128ꢀ ꢀ0850Hꢀꢀ  
2144ꢀ ꢀ0860Hꢀꢀ  
2160ꢀ ꢀ0870Hꢀꢀ  
2176ꢀ ꢀ0880Hꢀꢀ  
2192ꢀ ꢀ0890Hꢀꢀ  
2208ꢀ ꢀ08A0Hꢀꢀ  
2224ꢀ ꢀ08B0Hꢀꢀ  
Optimal start / stop moduleꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
2240ꢀ ꢀ08C0Hꢀꢀ  
2272ꢀ ꢀ08E0Hꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 27 of 51  
General control module  
Relative Item  
0ꢀꢀ  
1ꢀꢀ  
2ꢀꢀ  
3ꢀꢀ  
4ꢀꢀ  
5ꢀꢀ  
6ꢀꢀ  
7ꢀꢀ  
Signal Condition  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀꢁꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀWordꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
Read/Write  
Readꢀꢀ  
ꢀWriteꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀꢁꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀReadꢀꢀ  
Johnson Tag  
ꢀUNITꢀꢀ  
ꢀSUPꢀꢀ  
Description  
Deviceꢀmodel.ꢀForꢀDXꢁ9100ꢀalwaysꢀ5ꢀ  
Supervisoryꢀcentralꢀcontrolꢀ  
Maintenanceꢀcontrolꢀ  
Diagnisticsꢀ  
Digitalꢀinputꢀcountersꢀ  
Triacꢀoutputꢀstatusꢀ  
Digitalꢀinputꢀstatusꢀ  
Analogꢀinputꢀstatusꢀ  
Logicꢀresultsꢀ37637ꢀ  
Logicꢀresultsꢀ17ꢁ32ꢀ  
Logicꢀconstantsꢀ37637ꢀ  
Logicꢀconstantsꢀ17ꢁ32ꢀ  
Spareꢀ  
DI1ꢀpulseꢀcountꢀ  
DI2ꢀpulseꢀcountꢀ  
DI3ꢀpulseꢀcountꢀ  
DI4ꢀpulseꢀcountꢀ  
DI5ꢀpulseꢀcountꢀ  
DI6ꢀpulseꢀcountꢀ  
DI7ꢀpulseꢀcountꢀ  
DI8ꢀpulseꢀcountꢀ  
ꢀMNTꢀꢀ  
ꢀDIAGꢀꢀ  
ꢀDICTꢀꢀ  
ꢀTOSꢀꢀ  
ꢀDISꢀꢀ  
ꢀAISꢀꢀ  
8ꢀꢀ  
9ꢀꢀ  
ꢀLRST1ꢀꢀ  
ꢀLRST2ꢀꢀ  
ꢀLCOS1ꢀꢀ  
ꢀLCOS2ꢀꢀ  
ꢀꢁꢀꢀ  
ꢀCNTR1ꢀꢀ  
ꢀCNTR2ꢀꢀ  
ꢀCNTR3ꢀꢀ  
ꢀCNTR4ꢀꢀ  
ꢀCNTR5ꢀꢀ  
ꢀCNTR6ꢀꢀ  
ꢀCNTR7ꢀꢀ  
ꢀCNTR8ꢀꢀ  
ꢀPASSꢀꢀ  
ꢀPC1ꢀꢀ  
ꢀPC2ꢀꢀ  
ꢀPC3ꢀꢀ  
ꢀPC4ꢀꢀ  
ꢀPC5ꢀꢀ  
ꢀPC6ꢀꢀ  
ꢀPC7ꢀꢀ  
ꢀPC8ꢀꢀ  
ꢀUIAꢀꢀ  
10ꢀꢀ  
11ꢀꢀ  
12ꢀꢀ  
13ꢀꢀ  
14ꢀꢀ  
15ꢀꢀ  
16ꢀꢀ  
17ꢀꢀ  
18ꢀꢀ  
19ꢀꢀ  
20ꢀꢀ  
21ꢀꢀ  
22ꢀꢀ  
23ꢀꢀ  
24ꢀꢀ  
25ꢀꢀ  
26ꢀꢀ  
27ꢀꢀ  
28ꢀꢀ  
29ꢀꢀ  
30ꢀꢀ  
31ꢀꢀ  
32ꢀꢀ  
33ꢀꢀ  
34ꢀꢀ  
35ꢀꢀ  
36ꢀꢀ  
37ꢀꢀ  
38ꢀꢀ  
39ꢀꢀ  
40ꢀꢀ  
41ꢀꢀ  
42ꢀꢀ  
43ꢀꢀ  
Passwordꢀcodeꢀ  
PrescalerꢀDI1ꢀcounterꢀ  
PrescalerꢀDI2ꢀcounterꢀ  
PrescalerꢀDI3ꢀcounterꢀ  
PrescalerꢀDI4ꢀcounterꢀ  
PrescalerꢀDI5ꢀcounterꢀ  
PrescalerꢀDI6ꢀcounterꢀ  
PrescalerꢀDI7ꢀcounterꢀ  
PrescalerꢀDI8ꢀcounterꢀ  
Userꢀinterfaceꢀaddressꢀ  
Alarmꢀdisableꢀconditionꢀsourceꢀ  
DXꢁ9100ꢀtypeꢀsettingsꢀ  
Standardꢀalgorithmꢀtypeꢀ  
Analogꢀconstantꢀ1ꢀ  
Analogꢀconstantꢀ2ꢀ  
Analogꢀconstantꢀ3ꢀ  
Analogꢀconstantꢀ4ꢀ  
Analogꢀconstantꢀ5ꢀ  
Analogꢀconstantꢀ6ꢀ  
Analogꢀconstantꢀ7ꢀ  
Analogꢀconstantꢀ8ꢀ  
PLCꢀcontrolꢀandꢀstatusꢀ  
PLCꢀprogramꢀcounterꢀ  
ꢀALD@ꢀꢀ  
ꢀDXS1ꢀꢀ  
ꢀALGꢀꢀ  
ꢀACO1ꢀꢀ  
ꢀACO2ꢀꢀ  
ꢀACO3ꢀꢀ  
ꢀACO4ꢀꢀ  
ꢀACO5ꢀꢀ  
ꢀACO6ꢀꢀ  
ꢀACO7ꢀꢀ  
ꢀACO8ꢀꢀ  
ꢀPLCNTꢀꢀ  
ꢀPLCPCꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 28 of 51  
Programmable Module Type  
Relative Item  
0ꢀꢀ  
1ꢀꢀ  
2ꢀꢀ  
3ꢀꢀ  
4ꢀꢀ  
5ꢀꢀ  
6ꢀꢀ  
7ꢀꢀ  
Signal Condition  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
Read/Write  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
Johnson Tag  
ꢀPMTYPꢀꢀ  
ꢀPMOPTꢀꢀ  
ꢀPMF1ꢀꢀ  
ꢀPMF2ꢀꢀ  
ꢀPMF3ꢀꢀ  
ꢀPMF4ꢀꢀ  
ꢀPMF5ꢀꢀ  
ꢀPMF6ꢀꢀ  
ꢀPMF7ꢀꢀ  
Description  
Programmableꢀmoduleꢀtypeꢀ  
Programmableꢀmoduleꢀoptionsꢀ  
Functionꢀchannelꢀnumberꢀ1ꢀꢁꢀF1ꢀ  
Functionꢀchannelꢀnumberꢀ2ꢀꢁꢀF2ꢀ  
Functionꢀchannelꢀnumberꢀ3ꢀꢁꢀF3ꢀ  
Functionꢀchannelꢀnumberꢀ4ꢀꢁꢀF4ꢀ  
Functionꢀchannelꢀnumberꢀ5ꢀꢁꢀF5ꢀ  
Functionꢀchannelꢀnumberꢀ6ꢀꢁꢀF6ꢀ  
Functionꢀchannelꢀnumberꢀ7ꢀꢁꢀF7ꢀ  
Functionꢀchannelꢀnumberꢀ8ꢀꢁꢀF8ꢀ  
InputꢀconnectionꢀꢁꢀI1@ꢀ  
InputꢀconnectionꢀꢁꢀI2@ꢀ  
InputꢀconnectionꢀꢁꢀI3@ꢀ  
InputꢀconnectionꢀꢁꢀI4@ꢀ  
InputꢀconnectionꢀꢁꢀI5@ꢀ  
InputꢀconnectionꢀꢁꢀI6@ꢀ  
InputꢀconnectionꢀꢁꢀI7@ꢀ  
InputꢀconnectionꢀꢁꢀI8@ꢀ  
InputꢀconnectionꢀꢁꢀI9@ꢀ  
InputꢀconnectionꢀꢁꢀI10@ꢀ  
InputꢀconnectionꢀꢁꢀI11@ꢀ  
InputꢀconnectionꢀꢁꢀI12@ꢀ  
InputꢀconnectionꢀꢁꢀI13@ꢀ  
InputꢀconnectionꢀꢁꢀI14@ꢀ  
InputꢀconnectionꢀꢁꢀI15@ꢀ  
InputꢀconnectionꢀꢁꢀI16@ꢀ  
ModuleꢀconstantꢀꢁꢀK1ꢀ  
8ꢀꢀ  
9ꢀꢀ  
ꢀPMF8ꢀꢀ  
10ꢀꢀ  
11ꢀꢀ  
12ꢀꢀ  
13ꢀꢀ  
14ꢀꢀ  
15ꢀꢀ  
16ꢀꢀ  
17ꢀꢀ  
18ꢀꢀ  
19ꢀꢀ  
20ꢀꢀ  
21ꢀꢀ  
22ꢀꢀ  
23ꢀꢀ  
24ꢀꢀ  
25ꢀꢀ  
26ꢀꢀ  
27ꢀꢀ  
28ꢀꢀ  
29ꢀꢀ  
30ꢀꢀ  
31ꢀꢀ  
32ꢀꢀ  
33ꢀꢀ  
34ꢀꢀ  
35ꢀꢀ  
36ꢀꢀ  
37ꢀꢀ  
38ꢀꢀ  
39ꢀꢀ  
40ꢀꢀ  
41ꢀꢀ  
42ꢀꢀ  
43ꢀꢀ  
44ꢀꢀ  
45ꢀꢀ  
46ꢀꢀ  
47ꢀꢀ  
48ꢀꢀ  
49ꢀꢀ  
50ꢀꢀ  
51ꢀꢀ  
52ꢀꢀ  
53ꢀꢀ  
54ꢀꢀ  
55ꢀꢀ  
56ꢀꢀ  
ꢀPMI1@ꢀꢀ  
ꢀPMI2@ꢀꢀ  
ꢀPMI3@ꢀꢀ  
ꢀPMI4@ꢀꢀ  
ꢀPMI5@ꢀꢀ  
ꢀPMI6@ꢀꢀ  
ꢀPMI7@ꢀꢀ  
ꢀPMI8@ꢀꢀ  
ꢀPMI9@ꢀꢀ  
ꢀPMI10@ꢀꢀ  
ꢀPMI11@ꢀꢀ  
ꢀPMI12@ꢀꢀ  
ꢀPMI13@ꢀꢀ  
ꢀPMI14@ꢀꢀ  
ꢀPMI15@ꢀꢀ  
ꢀPMI16@ꢀꢀ  
ꢀPMK01ꢀꢀ  
ꢀPMK02ꢀꢀ  
ꢀPMK03ꢀꢀ  
ꢀPMK04ꢀꢀ  
ꢀPMK05ꢀꢀ  
ꢀPMK06ꢀꢀ  
ꢀPMK07ꢀꢀ  
ꢀPMK08ꢀꢀ  
ꢀPMK09ꢀꢀ  
ꢀPMK10ꢀꢀ  
ꢀPMK11ꢀꢀ  
ꢀPMK12ꢀꢀ  
ꢀPMK13ꢀꢀ  
ꢀPMK14ꢀꢀ  
ꢀPMK15ꢀꢀ  
ꢀPMK16ꢀꢀ  
ꢀPMK17ꢀꢀ  
ꢀPMK18ꢀꢀ  
ꢀPMK19ꢀꢀ  
ꢀPMK20ꢀꢀ  
ꢀPMK21ꢀꢀ  
ꢀPMK22ꢀꢀ  
ꢀPMK23ꢀꢀ  
ꢀPMK24ꢀꢀ  
ꢀPMK25ꢀꢀ  
ꢀPMK26ꢀꢀ  
ꢀPMK27ꢀꢀ  
ꢀPMK28ꢀꢀ  
ꢀPMK29ꢀꢀ  
ꢀPMK30ꢀꢀ  
ꢀPMK31ꢀꢀ  
ModuleꢀconstantꢀꢁꢀK2ꢀ  
ModuleꢀconstantꢀꢁꢀK3ꢀ  
ModuleꢀconstantꢀꢁꢀK4ꢀ  
ModuleꢀconstantꢀꢁꢀK5ꢀ  
ModuleꢀconstantꢀꢁꢀK6ꢀ  
ModuleꢀconstantꢀꢁꢀK7ꢀ  
ModuleꢀconstantꢀꢁꢀK8ꢀ  
ModuleꢀconstantꢀꢁꢀK9ꢀ  
ModuleꢀconstantꢀꢁꢀK10ꢀ  
ModuleꢀconstantꢀꢁꢀK11ꢀ  
ModuleꢀconstantꢀꢁꢀK12ꢀ  
ModuleꢀconstantꢀꢁꢀK13ꢀ  
ModuleꢀconstantꢀꢁꢀK14ꢀ  
ModuleꢀconstantꢀꢁꢀK15ꢀ  
ModuleꢀconstantꢀꢁꢀK16ꢀ  
ModuleꢀconstantꢀꢁꢀK17ꢀ  
ModuleꢀconstantꢀꢁꢀK18ꢀ  
ModuleꢀconstantꢀꢁꢀK19ꢀ  
ModuleꢀconstantꢀꢁꢀK20ꢀ  
ModuleꢀconstantꢀꢁꢀK21ꢀ  
ModuleꢀconstantꢀꢁꢀK22ꢀ  
ModuleꢀconstantꢀꢁꢀK23ꢀ  
ModuleꢀconstantꢀꢁꢀK24ꢀ  
ModuleꢀconstantꢀꢁꢀK25ꢀ  
ModuleꢀconstantꢀꢁꢀK26ꢀ  
ModuleꢀconstantꢀꢁꢀK27ꢀ  
ModuleꢀconstantꢀꢁꢀK28ꢀ  
ModuleꢀconstantꢀꢁꢀK29ꢀ  
ModuleꢀconstantꢀꢁꢀK30ꢀ  
ModuleꢀconstantꢀꢁꢀK31ꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 29 of 51  
Programmable Module Type  
Relative Item  
57ꢀꢀ  
58ꢀꢀ  
59ꢀꢀ  
60ꢀꢀ  
61ꢀꢀ  
62ꢀꢀ  
63ꢀꢀ  
64ꢀꢀ  
65ꢀꢀ  
66ꢀꢀ  
67ꢀꢀ  
68ꢀꢀ  
69ꢀꢀ  
70ꢀꢀ  
71ꢀꢀ  
72ꢀꢀ  
73ꢀꢀ  
74ꢀꢀ  
75ꢀꢀ  
76ꢀꢀ  
77ꢀꢀ  
78ꢀꢀ  
79ꢀꢀ  
80ꢀꢀ  
Signal Condition  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
Read/Write  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀReadꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
Johnson Tag  
ꢀPMK32ꢀꢀ  
ꢀPMK33ꢀꢀ  
ꢀPMK34ꢀꢀ  
ꢀPMOU1ꢀꢀ  
ꢀPMOU2ꢀꢀ  
ꢀPMOU3ꢀꢀ  
ꢀPMOU4ꢀꢀ  
ꢀPMOU5ꢀꢀ  
ꢀPMOU6ꢀꢀ  
ꢀPMOU7ꢀꢀ  
ꢀPMOU8ꢀꢀ  
ꢀPMAX1ꢀꢀ  
ꢀPMAX2ꢀꢀ  
ꢀPMHDCꢀꢀ  
ꢀPMDOꢀꢀ  
Description  
ModuleꢀconstantꢀꢁꢀK32ꢀ  
ModuleꢀconstantꢀꢁꢀK33ꢀ  
ModuleꢀconstantꢀꢁꢀK34ꢀ  
Outputꢀchannelꢀ1ꢀ  
Outputꢀchannelꢀ2ꢀ  
Outputꢀchannelꢀ3ꢀ  
Outputꢀchannelꢀ4ꢀ  
Outputꢀchannelꢀ5ꢀ  
Outputꢀchannelꢀ6ꢀ  
Outputꢀchannelꢀ7ꢀ  
Outputꢀchannelꢀ8ꢀ  
Auxiliaryꢀoutputꢀ1ꢀ  
Auxiliaryꢀoutputꢀ2ꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
Holdꢀmodeꢀcontrol/statusꢀ  
Logicꢀoutputꢀcontrolꢀandꢀstatusꢀ  
Programmableꢀmoduleꢀstatusꢀ  
Accumulatorꢀchannelꢀ1ꢀ  
Accumulatorꢀchannelꢀ2ꢀ  
Accumulatorꢀchannelꢀ3ꢀ  
Accumulatorꢀchannelꢀ4ꢀ  
Accumulatorꢀchannelꢀ5ꢀ  
Accumulatorꢀchannelꢀ6ꢀ  
Accumulatorꢀchannelꢀ7ꢀ  
Accumulatorꢀchannelꢀ8ꢀ  
ꢀPMSTꢀꢀ  
ꢀPMAC1ꢀꢀ  
ꢀPMAC2ꢀꢀ  
ꢀPMAC3ꢀꢀ  
ꢀPMAC4ꢀꢀ  
ꢀPMAC5ꢀꢀ  
ꢀPMAC6ꢀꢀ  
ꢀPMAC7ꢀꢀ  
ꢀPMAC8ꢀꢀ  
Analog Input Modules  
Relative Item  
Signal Condition  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
Read/Write  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
Johnson Tag  
ꢀAITꢀꢀ  
ꢀHRꢀꢀ  
Description  
0ꢀꢀ  
1ꢀꢀ  
2ꢀꢀ  
3ꢀꢀ  
4ꢀꢀ  
5ꢀꢀ  
6ꢀꢀ  
7ꢀꢀ  
8ꢀꢀ  
9ꢀꢀ  
10ꢀꢀ  
ꢀAnalogꢀinoutꢀtypeꢀ  
ꢀHighꢀrangeꢀinputꢀ  
ꢀLowꢀrangeꢀinputꢀ  
ꢀHighꢀalarmꢀlimitꢀ  
ꢀLowꢀalarmꢀlimitꢀ  
ꢀFilterꢀconstantꢀ  
ꢀDifferentialꢀonꢀalarmꢀlimitꢀ(units)ꢀ  
ꢀAnalogꢀinputꢀvalueꢀ  
ꢀAnalogꢀinputꢀ%ꢀ  
ꢀAnalogꢀinputꢀinꢀcountsꢀ  
ꢀAnalogꢀinputꢀstatusꢀ  
ꢀLRꢀꢀ  
ꢀHIAꢀꢀ  
ꢀLOAꢀꢀ  
ꢀFTCꢀꢀ  
ꢀADFꢀꢀ  
ꢀAIꢀꢀ  
ꢀAI%ꢀꢀ  
ꢀADCꢀꢀ  
ꢀAISTꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
Analog Output Modules  
Relative Item  
0ꢀꢀ  
1ꢀꢀ  
2ꢀꢀ  
3ꢀꢀ  
4ꢀꢀ  
5ꢀꢀ  
6ꢀꢀ  
7ꢀꢀ  
8ꢀꢀ  
9ꢀꢀ  
10ꢀꢀ  
11ꢀꢀ  
12ꢀꢀ  
Signal Condition  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
Read/Write Johnson Tag  
Description  
Analogꢀoutputꢀtypeꢀ  
Sourceꢀofꢀanalogꢀoutputꢀmoduleꢀ  
Outputꢀforcingꢀlogicꢀconnectionꢀ  
Outputꢀhighꢀrangeꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀAOTꢀꢀ  
ꢀAO@ꢀꢀ  
ꢀAOF@ꢀꢀ  
ꢀHROꢀꢀ  
ꢀLROꢀꢀ  
Outputꢀlowꢀrangeꢀ  
ꢀOFLꢀꢀ  
Outputꢀ%ꢀvalueꢀinꢀforcingꢀmodeꢀ  
Outputꢀmoduleꢀoutputꢀvalueꢀ%ꢀ  
Analogꢀoutputꢀcontrolꢀandꢀstatusꢀ  
Outputꢀhighꢀlimitꢀ  
ꢀOUTꢀꢀ  
ꢀAOCꢀꢀ  
ꢀHLOꢀꢀ  
ꢀFPꢀꢀ  
ꢀLLOꢀꢀ  
Outputꢀlowꢀlimitꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀINC@ꢀꢀ  
ꢀDEC@ꢀꢀ  
ꢀENL@ꢀꢀ  
DDCꢀincreaseꢀlogicꢀconnectionꢀ  
DDCꢀdecreaseꢀlogicꢀconnectionꢀ  
Limitꢀfunctionꢀenableꢀlogicꢀconnectionꢀ  
Digital Output Modules  
Relative Item  
Signal Condition  
Read/Write Johnson Tag  
Description  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 30 of 51  
Digital Output Modules  
Read/Write Johnson Tag  
Relative Item  
0ꢀꢀ  
1ꢀꢀ  
2ꢀꢀ  
3ꢀꢀ  
4ꢀꢀ  
5ꢀꢀ  
6ꢀꢀ  
7ꢀꢀ  
8ꢀꢀ  
9ꢀꢀ  
10ꢀꢀ  
11ꢀꢀ  
12ꢀꢀ  
13ꢀꢀ  
14ꢀꢀ  
15ꢀꢀ  
Signal Condition  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
Description  
Digitalꢀoutputꢀoptionsꢀ  
Sourceꢀofꢀdigitalꢀoutputꢀmoduleꢀ  
Sourceꢀofꢀfeedbackꢀsignalꢀ  
Outputꢀforcingꢀlogicꢀconnectionꢀ  
Outputꢀhighꢀrangeꢀ  
Outputꢀlowꢀrangeꢀ  
PATꢀoutputꢀfullꢀstrokeꢀtime/DATꢀcycleꢀ  
PATꢀdeadbandꢀ  
Outputꢀhighꢀlimitꢀ  
Outputꢀlowꢀlimitꢀ  
Outputꢀ%ꢀvalueꢀinꢀforcingꢀmodeꢀ  
Outputꢀmoduleꢀoutputꢀvalueꢀ%ꢀ  
Logicꢀoutputꢀcontrolꢀandꢀstatusꢀ  
DDCꢀincreaseꢀlogicꢀconnectionꢀ  
DDCꢀdecreaseꢀlogicꢀconnectionꢀ  
Limitꢀfunctionꢀenableꢀlogicꢀconnectionꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀDOTꢀꢀ  
ꢀDO@ꢀꢀ  
ꢀFB@ꢀꢀ  
ꢀDOF@ꢀꢀ  
ꢀHROꢀꢀ  
ꢀLROꢀꢀ  
ꢀFSTꢀꢀ  
ꢀDBꢀꢀ  
ꢀHLOꢀꢀ  
ꢀLLOꢀꢀ  
ꢀOFLꢀꢀ  
ꢀOUTꢀꢀ  
ꢀDOCꢀꢀ  
ꢀINC@ꢀꢀ  
ꢀDEC@ꢀꢀ  
ꢀENL@ꢀꢀ  
Extension Modules  
Read/Write Johnson Tag  
Relative Item  
0ꢀꢀ  
1ꢀꢀ  
2ꢀꢀ  
3ꢀꢀ  
4ꢀꢀ  
5ꢀꢀ  
6ꢀꢀ  
7ꢀꢀ  
Signal Condition  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
Description  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀXTIOMAPꢀꢀ  
ꢀXTIOTYPꢀꢀ  
ꢀXTIOMODꢀꢀ  
ꢀXTADXꢀꢀ  
ꢀXTI1@ꢀꢀ  
ꢀXTI2@ꢀꢀ  
ꢀXTI3@ꢀꢀ  
ꢀXTI4@ꢀꢀ  
ꢀXTI5@ꢀꢀ  
ExtensionꢀmoduleꢀI/Oꢀmapꢀ  
ExtensionꢀmoduleꢀI/Oꢀtypeꢀ  
ExtensionꢀmoduleꢀI/Oꢀmodeꢀ  
Extensionꢀmoduleꢀaddressꢀ0ꢁ255ꢀ  
PointꢀconnectionꢀꢁꢀI1ꢀ  
PointꢀconnectionꢀꢁꢀI2ꢀ  
PointꢀconnectionꢀꢁꢀI3ꢀ  
PointꢀconnectionꢀꢁꢀI4ꢀ  
PointꢀconnectionꢀꢁꢀI5ꢀ  
8ꢀꢀ  
9ꢀꢀ  
ꢀXTI6@ꢀꢀ  
ꢀXTI7@ꢀꢀ  
ꢀXTI8@ꢀꢀ  
PointꢀconnectionꢀꢁꢀI6ꢀ  
PointꢀconnectionꢀꢁꢀI7ꢀ  
PointꢀconnectionꢀꢁꢀI8ꢀ  
10ꢀꢀ  
11ꢀꢀ  
12ꢀꢀ  
13ꢀꢀ  
14ꢀꢀ  
15ꢀꢀ  
16ꢀꢀ  
17ꢀꢀ  
18ꢀꢀ  
19ꢀꢀ  
20ꢀꢀ  
21ꢀꢀ  
22ꢀꢀ  
23ꢀꢀ  
24ꢀꢀ  
25ꢀꢀ  
26ꢀꢀ  
27ꢀꢀ  
28ꢀꢀ  
29ꢀꢀ  
30ꢀꢀ  
31ꢀꢀ  
32ꢀꢀ  
33ꢀꢀ  
34ꢀꢀ  
35ꢀꢀ  
36ꢀꢀ  
37ꢀꢀ  
ꢀXTHR01ꢀꢀ  
ꢀXTLR01ꢀꢀ  
ꢀXTHR02ꢀꢀ  
ꢀXTLR02ꢀꢀ  
ꢀXTHR03ꢀꢀ  
ꢀXTLR03ꢀꢀ  
ꢀXTHR04ꢀꢀ  
ꢀXTLR04ꢀꢀ  
ꢀXTHR05ꢀꢀ  
ꢀXTLR05ꢀꢀ  
ꢀXTHR06ꢀꢀ  
ꢀXTLR06ꢀꢀ  
ꢀXTHR07ꢀꢀ  
ꢀXTLR07ꢀꢀ  
ꢀXTHR08ꢀꢀ  
ꢀXTLR08ꢀꢀ  
ꢀXTHIA1ꢀꢀ  
ꢀXTLOA1ꢀꢀ  
ꢀXTHIA2ꢀꢀ  
ꢀXTLOA2ꢀꢀ  
ꢀXTHIA3ꢀꢀ  
ꢀXTLOA3ꢀꢀ  
ꢀXTHIA4ꢀꢀ  
ꢀXTLOA4ꢀꢀ  
ꢀXTHIA5ꢀꢀ  
ꢀXTLOA5ꢀꢀ  
Highꢀoutputꢀrangeꢀpointꢀ1ꢀ  
Lowꢀoutputꢀrangeꢀpointꢀ1ꢀ  
Highꢀoutputꢀrangeꢀpointꢀ2ꢀ  
Lowꢀoutputꢀrangeꢀpointꢀ2ꢀ  
Highꢀoutputꢀrangeꢀpointꢀ3ꢀ  
Lowꢀoutputꢀrangeꢀpointꢀ3ꢀ  
Highꢀoutputꢀrangeꢀpointꢀ4ꢀ  
Lowꢀoutputꢀrangeꢀpointꢀ4ꢀ  
Highꢀoutputꢀrangeꢀpointꢀ5ꢀ  
Lowꢀoutputꢀrangeꢀpointꢀ5ꢀ  
Highꢀoutputꢀrangeꢀpointꢀ6ꢀ  
Lowꢀoutputꢀrangeꢀpointꢀ6ꢀ  
Highꢀoutputꢀrangeꢀpointꢀ7ꢀ  
Lowꢀoutputꢀrangeꢀpointꢀ7ꢀ  
Highꢀoutputꢀrangeꢀpointꢀ8ꢀ  
Lowꢀoutputꢀrangeꢀpointꢀ8ꢀ  
Highꢀalarmꢀlimitꢀpointꢀ1ꢀ  
Lowꢀalarmꢀlimitꢀpointꢀ1ꢀ  
Highꢀalarmꢀlimitꢀpointꢀ2ꢀ  
Lowꢀalarmꢀlimitꢀpointꢀ2ꢀ  
Highꢀalarmꢀlimitꢀpointꢀ3ꢀ  
Lowꢀalarmꢀlimitꢀpointꢀ3ꢀ  
Highꢀalarmꢀlimitꢀpointꢀ4ꢀ  
Lowꢀalarmꢀlimitꢀpointꢀ4ꢀ  
Highꢀalarmꢀlimitꢀpointꢀ5ꢀ  
Lowꢀalarmꢀlimitꢀpointꢀ5ꢀ  
ꢀFPꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 31 of 51  
Extension Modules  
Read/Write Johnson Tag  
Relative Item  
38ꢀꢀ  
39ꢀꢀ  
40ꢀꢀ  
41ꢀꢀ  
42ꢀꢀ  
43ꢀꢀ  
44ꢀꢀ  
45ꢀꢀ  
46ꢀꢀ  
47ꢀꢀ  
48ꢀꢀ  
49ꢀꢀ  
50ꢀꢀ  
51ꢀꢀ  
52ꢀꢀ  
53ꢀꢀ  
54ꢀꢀ  
55ꢀꢀ  
56ꢀꢀ  
57ꢀꢀ  
58ꢀꢀ  
59ꢀꢀ  
60ꢀꢀ  
61ꢀꢀ  
62ꢀꢀ  
63ꢀꢀ  
64ꢀꢀ  
65ꢀꢀ  
66ꢀꢀ  
67ꢀꢀ  
68ꢀꢀ  
69ꢀꢀ  
70ꢀꢀ  
71ꢀꢀ  
72ꢀꢀ  
Signal Condition  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀLONGꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
Description  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀXTHIA6ꢀꢀ  
ꢀXTLOA6ꢀꢀ  
ꢀXTHIA7ꢀꢀ  
ꢀXTLOA7ꢀꢀ  
ꢀXTHIA8ꢀꢀ  
ꢀXTLOA8ꢀꢀ  
ꢀXTAISꢀꢀ  
ꢀXTAI1ꢀꢀ  
ꢀXTAI2ꢀꢀ  
ꢀXTAI3ꢀꢀ  
ꢀXTAI4ꢀꢀ  
ꢀXTAI5ꢀꢀ  
Highꢀalarmꢀlimitꢀpointꢀ6ꢀ  
Lowꢀalarmꢀlimitꢀpointꢀ6ꢀ  
Highꢀalarmꢀlimitꢀpointꢀ7ꢀ  
Lowꢀalarmꢀlimitꢀpointꢀ7ꢀ  
Highꢀalarmꢀlimitꢀpointꢀ8ꢀ  
Lowꢀalarmꢀlimitꢀpointꢀ8ꢀ  
Extensionꢀmoduleꢀalarmsꢀ  
Analogꢀinputꢀvalueꢀ1ꢀ  
Analogꢀinputꢀvalueꢀ2ꢀ  
Analogꢀinputꢀvalueꢀ3ꢀ  
Analogꢀinputꢀvalueꢀ4ꢀ  
ꢀAnalogꢀinputꢀvalueꢀ5ꢀ  
ꢀXTAI6ꢀꢀ  
ꢀXTAI7ꢀꢀ  
ꢀXTAI8ꢀꢀ  
ꢀAnalogꢀinputꢀvalueꢀ6ꢀ  
ꢀAnalogꢀinputꢀvalueꢀ7ꢀ  
ꢀAnalogꢀinputꢀvalueꢀ8ꢀ  
ꢀXTAO1ꢀꢀ  
ꢀXTAO2ꢀꢀ  
ꢀXTAO3ꢀꢀ  
ꢀXTAO4ꢀꢀ  
ꢀXTAO5ꢀꢀ  
ꢀXTAO6ꢀꢀ  
ꢀXTAO7ꢀꢀ  
ꢀXTAO8ꢀꢀ  
ꢀXTDIC1ꢀꢀ  
ꢀXTDIC2ꢀꢀ  
ꢀXTDIC3ꢀꢀ  
ꢀXTDIC4ꢀꢀ  
ꢀXTDIC5ꢀꢀ  
ꢀXTDIC6ꢀꢀ  
ꢀXTDIC7ꢀꢀ  
ꢀXTDIC8ꢀꢀ  
ꢀXTCNTꢀꢀ  
ꢀXTDOꢀꢀ  
ꢀAnalogꢀoutputꢀvalueꢀ1ꢀ  
ꢀAnalogꢀoutputꢀvalueꢀ2ꢀ  
ꢀAnalogꢀoutputꢀvalueꢀ3ꢀ  
ꢀAnalogꢀoutputꢀvalueꢀ4ꢀ  
ꢀAnalogꢀoutputꢀvalueꢀ5ꢀ  
ꢀAnalogꢀoutputꢀvalueꢀ6ꢀ  
ꢀAnalogꢀoutputꢀvalueꢀ7ꢀ  
ꢀAnalogꢀoutputꢀvalueꢀ8ꢀ  
ꢀDigitalꢀinputꢀ1ꢀpulseꢀcountꢀ  
ꢀDigitalꢀinputꢀ2ꢀpulseꢀcountꢀ  
ꢀDigitalꢀinputꢀ3ꢀpulseꢀcountꢀ  
ꢀDigitalꢀinputꢀ4ꢀpulseꢀcountꢀ  
ꢀDigitalꢀinputꢀ5ꢀpulseꢀcountꢀ  
ꢀDigitalꢀinputꢀ6ꢀpulseꢀcountꢀ  
ꢀDigitalꢀinputꢀ7ꢀpulseꢀcountꢀ  
ꢀDigitalꢀinputꢀ8ꢀpulseꢀcountꢀ  
ꢀExtensionꢀmoduleꢀholdꢀcontrolꢀ  
ꢀLogicꢀoutputsꢀcontrolꢀandꢀstatusꢀ  
ꢀLogicꢀinputsꢀstatusꢀ  
ꢀXTDIꢀꢀ  
ꢀXTSTCꢀꢀ  
ꢀExtensionꢀmoduleꢀlocalꢀstatusꢀ  
Time schedule modulesꢀ  
Relative Item  
Signal Condition  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
Read/Write  
Johnson Tag  
ꢀTSOPTꢀꢀ  
ꢀTSEX@ꢀꢀ  
ꢀTSON@ꢀꢀ  
ꢀTSOF@ꢀꢀ  
ꢀTSXTMꢀꢀ  
ꢀTSTIMꢀꢀ  
Description  
0ꢀꢀ  
1ꢀꢀ  
2ꢀꢀ  
3ꢀꢀ  
4ꢀꢀ  
5ꢀꢀ  
6ꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
TimeꢀscheduleꢀoptionsꢀLSBꢀ  
Externalꢀextensionꢀlogicalꢀconnectionꢀ  
Onꢀforcingꢀlogicalꢀconnectionꢀ  
Offꢀforcingꢀlogicalꢀconnectionꢀ  
Extensionꢀtimeꢀ(min)ꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
Timeꢀtoꢀnextꢀeventꢀ(min)ꢀ  
Timeꢀscheduleꢀstatusꢀ  
ꢀTSSTAꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 32 of 51  
Programmable modules  
64ꢀ ꢀ0040Hꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
9ꢀ  
160ꢀ ꢀ00A0Hꢀꢀ  
256ꢀ ꢀ0100Hꢀꢀ  
352ꢀ ꢀ0160Hꢀꢀ  
448ꢀ ꢀ01C0Hꢀꢀ  
544ꢀ ꢀ0220Hꢀꢀ  
640ꢀ ꢀ0280Hꢀꢀ  
736ꢀ ꢀ02E0Hꢀꢀ  
832ꢀ ꢀ0340Hꢀꢀ  
928ꢀ ꢀ03A0Hꢀꢀ  
1024ꢀ ꢀ0400Hꢀꢀ  
1120ꢀ ꢀ0460Hꢀꢀ  
10ꢀ  
11ꢀ  
12ꢀ  
Analog input modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
1216ꢀ ꢀ04C0Hꢀꢀ  
1232ꢀ ꢀ04D0Hꢀꢀ  
1248ꢀ ꢀ04E0Hꢀꢀ  
1264ꢀ ꢀ04F0Hꢀꢀ  
1280ꢀ ꢀ0500Hꢀꢀ  
1296ꢀ ꢀ0510Hꢀꢀ  
1312ꢀ ꢀ0520Hꢀꢀ  
1328ꢀ ꢀ0530Hꢀꢀ  
Analog output modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Versionꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
1344ꢀ ꢀ0540Hꢀꢀ  
1360ꢀ ꢀ0550Hꢀꢀ  
2ꢀ orꢀꢀlaterꢀ(newꢀforꢀversionꢀ6.0):ꢀ  
9ꢀ  
10ꢀ  
11ꢀ  
12ꢀ  
13ꢀ  
14ꢀ  
2304ꢀ ꢀ0900Hꢀꢀ  
2320ꢀ ꢀ0910Hꢀꢀ  
2336ꢀ ꢀ0920Hꢀꢀ  
2352ꢀ ꢀ0930Hꢀꢀ  
2368ꢀ ꢀ0940Hꢀꢀ  
2384ꢀ ꢀ0950Hꢀꢀ  
Digital output modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
1376ꢀ ꢀ0560Hꢀꢀ  
1392ꢀ ꢀ0570Hꢀꢀ  
1408ꢀ ꢀ0580Hꢀꢀ  
1424ꢀ ꢀ0590Hꢀꢀ  
1440ꢀ ꢀ05A0Hꢀꢀ  
1456ꢀ ꢀ05B0Hꢀꢀ  
Extension modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
1472ꢀ ꢀ05C0Hꢀꢀ  
1552ꢀ ꢀ0610Hꢀꢀ  
1632ꢀ ꢀ0660Hꢀꢀ  
1712ꢀ ꢀ06B0Hꢀꢀ  
1792ꢀ ꢀ0700Hꢀꢀ  
1872ꢀ ꢀ0750Hꢀꢀ  
1952ꢀ ꢀ07A0Hꢀꢀ  
2032ꢀ ꢀ07F0Hꢀꢀ  
Time schedule modulesꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
2112ꢀ ꢀ0840Hꢀꢀ  
2128ꢀ ꢀ0850Hꢀꢀ  
2144ꢀ ꢀ0860Hꢀꢀ  
2160ꢀ ꢀ0870Hꢀꢀ  
2176ꢀ ꢀ0880Hꢀꢀ  
2192ꢀ ꢀ0890Hꢀꢀ  
2208ꢀ ꢀ08A0Hꢀꢀ  
2224ꢀ ꢀ08B0Hꢀꢀ  
Optimal start / stop moduleꢀ  
Moduleꢀꢀ  
Moduleꢀꢀ  
1ꢀ  
2ꢀ  
2240ꢀ ꢀ08C0Hꢀꢀ  
2272ꢀ ꢀ08E0Hꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 33 of 51  
Appendix D.2. Metasys DC9100 Memory Map  
Note: The DC9100 is not currently supported by the FieldServer MetasysN2 Driver.  
The information below is for interest and future use only.  
PAGE 0  
Item  
DEC  
Item  
HEX  
Johnson  
Tag  
Signal Condition Read/Write  
Description  
Deviceꢀmodel.ꢀValueꢀalwaysꢀeitherꢀ2ꢀorꢀ  
12ꢀ  
0ꢀ  
0ꢀꢀByteꢀꢀ  
ꢀReadꢀꢀ  
ꢀMODLꢀꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
8ꢀ  
9ꢀ  
10ꢀꢀAꢀꢀ  
11ꢀꢀBꢀꢀ  
12ꢀꢀCꢀꢀ  
13ꢀꢀDꢀꢀ  
14ꢀꢀEꢀꢀ  
15ꢀꢀFꢀꢀ  
16ꢀ  
17ꢀ  
18ꢀ  
19ꢀ  
20ꢀ  
21ꢀ  
22ꢀ  
23ꢀ  
24ꢀ  
1ꢀꢀFPꢀꢀ  
2ꢀꢀFPꢀꢀ  
3ꢀꢀFPꢀꢀ  
4ꢀꢀFPꢀꢀ  
5ꢀꢀFPꢀꢀ  
6ꢀꢀFPꢀꢀ  
7ꢀꢀFPꢀꢀ  
8ꢀꢀFPꢀꢀ  
9ꢀꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀReadꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀINP1ꢀꢀ  
ꢀINP2ꢀꢀ  
ꢀINP3ꢀꢀ  
ꢀINP4ꢀꢀ  
ꢀINP5ꢀꢀ  
ꢀINP6ꢀꢀ  
ꢀINP7ꢀꢀ  
ꢀINP8ꢀꢀ  
ꢀAnalogꢀinputꢀ1ꢀ  
ꢀAnalogꢀinputꢀ2ꢀ  
ꢀAnalogꢀinputꢀ3ꢀ  
ꢀAnalogꢀinputꢀ4ꢀ  
ꢀAnalogꢀinputꢀ5ꢀ  
ꢀAnalogꢀinputꢀ6ꢀ  
ꢀAnalogꢀinputꢀ7ꢀ  
ꢀAnalogꢀinputꢀ8ꢀ  
ꢀNumericꢀcalculationꢀmodulꢀresultꢀ  
ꢀNumericꢀcalculationꢀmodulꢀresultꢀ  
ꢀNumericꢀcalculationꢀmodulꢀresultꢀ  
ꢀNumericꢀcalculationꢀmodulꢀresultꢀ  
ꢀRemoteꢀconstantꢀ1ꢀ  
ꢀRemoteꢀconstantꢀ2ꢀ  
ꢀRemoteꢀconstantꢀ3ꢀ  
ꢀRemoteꢀconstantꢀ4ꢀ  
ꢀControlꢀoutputꢀ1ꢀ  
ꢀControlꢀoutputꢀ2ꢀ  
ꢀControlꢀoutputꢀ3ꢀ  
ꢀControlꢀoutputꢀ4ꢀ  
ꢀControlꢀoutputꢀ5ꢀ  
ꢀNCM1ꢀꢀ  
ꢀNCM2ꢀꢀ  
ꢀNCM3ꢀꢀ  
ꢀNMC4ꢀꢀ  
ꢀREC1ꢀꢀ  
ꢀREC2ꢀꢀ  
ꢀREC3ꢀꢀ  
ꢀREC4ꢀꢀ  
ꢀOUT1ꢀꢀ  
ꢀOUT2ꢀꢀ  
ꢀOUT3ꢀꢀ  
ꢀOUT4ꢀꢀ  
ꢀOUT5ꢀꢀ  
ꢀOUT6ꢀꢀ  
ꢀOUT7ꢀꢀ  
ꢀOUT8ꢀꢀ  
ꢀWSP1ꢀꢀ  
ꢀWSP2ꢀꢀ  
ꢀWSP3ꢀꢀ  
ꢀWSP4ꢀꢀ  
ꢀWSP5ꢀꢀ  
ꢀWSP6ꢀꢀ  
ꢀWSP7ꢀꢀ  
ꢀWSP8ꢀꢀ  
ꢀSTW1ꢀꢀ  
ꢀSTW2ꢀꢀ  
ꢀSTW3ꢀꢀ  
ꢀSTW4ꢀꢀ  
ꢀSTW5ꢀꢀ  
ꢀSTW6ꢀꢀ  
ꢀSTW7ꢀꢀ  
ꢀSTW8ꢀꢀ  
ꢀDOUTꢀꢀ  
ꢀCHLDꢀꢀ  
ꢀCOMPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
10ꢀꢀFPꢀꢀ  
11ꢀꢀFPꢀꢀ  
12ꢀꢀFPꢀꢀ  
13ꢀꢀFPꢀꢀ  
14ꢀꢀFPꢀꢀ  
15ꢀꢀFPꢀꢀ  
16ꢀꢀFPꢀꢀ  
17ꢀꢀFPꢀꢀ  
18ꢀꢀFPꢀꢀ  
19ꢀꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀControlꢀoutputꢀ6ꢀ  
ꢀControlꢀoutputꢀ7ꢀ  
ꢀControlꢀoutputꢀ8ꢀ  
25ꢀ  
ꢀWorkingꢀsetpointꢀ1ꢀ  
ꢀWorkingꢀsetpointꢀ2ꢀ  
ꢀWorkingꢀsetpointꢀ3ꢀ  
ꢀWorkingꢀsetpointꢀ4ꢀ  
ꢀWorkingꢀsetpointꢀ5ꢀ  
ꢀWorkingꢀsetpointꢀ6ꢀ  
ꢀWorkingꢀsetpointꢀ7ꢀ  
ꢀWorkingꢀsetpointꢀ8ꢀ  
ꢀStatusꢀwordꢀ1ꢀ  
ꢀStatusꢀwordꢀ2ꢀ  
ꢀStatusꢀwordꢀ3ꢀ  
ꢀStatusꢀwordꢀ4ꢀ  
ꢀStatusꢀwordꢀ5ꢀ  
ꢀStatusꢀwordꢀ6ꢀ  
ꢀStatusꢀwordꢀ7ꢀ  
ꢀStatusꢀwordꢀ8ꢀ  
ꢀLogicꢀoutputꢀDDCꢀcontrolꢀ  
ꢀHoldꢀmodeꢀcontrolꢀ  
ꢀSupervisoryꢀmodeꢀcontrolꢀ  
26ꢀꢀ1Aꢀꢀ  
27ꢀꢀ1Bꢀꢀ  
28ꢀꢀ1Cꢀꢀ  
29ꢀꢀ1Dꢀꢀ  
30ꢀꢀ1Eꢀꢀ  
31ꢀꢀ1Fꢀꢀ  
32ꢀ  
33ꢀ  
34ꢀ  
35ꢀ  
36ꢀ  
37ꢀ  
38ꢀ  
39ꢀ  
40ꢀ  
41ꢀ  
42ꢀꢀ2Aꢀꢀ  
43ꢀꢀ2Bꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
20ꢀꢀFPꢀꢀ  
21ꢀꢀWordꢀꢀ  
22ꢀꢀWordꢀꢀ  
23ꢀꢀWordꢀꢀ  
24ꢀꢀWordꢀꢀ  
25ꢀꢀWordꢀꢀ  
26ꢀꢀWordꢀꢀ  
27ꢀꢀWordꢀꢀ  
28ꢀꢀWordꢀꢀ  
29ꢀꢀWordꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 34 of 51  
PAGE 0  
Johnson  
Tag  
Item  
DEC  
Item  
HEX  
Signal Condition Read/Write  
Description  
44ꢀꢀ2Cꢀꢀ  
45ꢀꢀ2Dꢀꢀ  
46ꢀꢀ2Eꢀꢀ  
47ꢀꢀ2Fꢀꢀ  
48ꢀ  
ꢀꢁꢀꢀ  
ꢀꢁꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀꢁꢀꢀ  
ꢀꢁꢀꢀ  
ꢀSpareꢀꢀ  
ꢀSpareꢀꢀ  
ꢀPV1@ꢀꢀ  
ꢀRS1@ꢀꢀ  
ꢀRV1@ꢀꢀ  
ꢀPB1@ꢀꢀ  
ꢀOF1@ꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀProcessꢀvariableꢀconnectionꢀ  
ꢀRemoteꢀsetpointꢀconnectionꢀ  
ꢀReferenceꢀvariableꢀconnectionꢀ  
ꢀProportionalꢀbandꢀconnectionꢀ  
ꢀOFFꢀmodeꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀSTANDꢁBYꢀmodeꢀlogicꢀcontrolꢀ  
connectionꢀ  
30ꢀꢀByteꢀꢀ  
31ꢀꢀByteꢀꢀ  
32ꢀꢀByteꢀꢀ  
49ꢀ  
50ꢀ  
51ꢀ  
52ꢀ  
53ꢀ  
33ꢀꢀByteꢀꢀ  
34ꢀꢀByteꢀꢀ  
35ꢀꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀSB1@ꢀꢀ  
ꢀRA1@ꢀꢀ  
ꢀEF1@ꢀꢀ  
ꢀReverseꢀactionꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀExternalꢀforcingꢀlogicꢀcontrolꢀ  
connectionꢀ  
54ꢀ  
55ꢀ  
56ꢀ  
57ꢀ  
58ꢀꢀ3Aꢀꢀ  
59ꢀꢀ3Bꢀꢀ  
60ꢀꢀ3Cꢀꢀ  
61ꢀꢀ3Dꢀꢀ  
62ꢀꢀ3Eꢀꢀ  
63ꢀꢀ3Fꢀꢀ  
64ꢀ  
36ꢀꢀByteꢀꢀ  
37ꢀꢀFPꢀꢀ  
38ꢀꢀFPꢀꢀ  
39ꢀꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀTYPE1ꢀꢀ  
ꢀLS1ꢀꢀ  
ꢀPB1ꢀꢀ  
ꢀTI1ꢀꢀ  
ꢀTD1ꢀꢀ  
ꢀHL1ꢀꢀ  
ꢀLL1ꢀꢀ  
ꢀBS1ꢀꢀ  
ꢀBO1ꢀꢀ  
ꢀAD1ꢀꢀ  
ꢀPV2@ꢀꢀ  
ꢀRS2@ꢀꢀ  
ꢀRV2@ꢀꢀ  
ꢀPB2@ꢀꢀ  
ꢀOF2@ꢀꢀ  
ꢀControllerꢀtypeꢀ  
ꢀLocalꢀsetpointꢀ  
ꢀProportionalꢀbandꢀ  
ꢀResetꢀactionꢀ  
ꢀRateꢀactionꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀUpperꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀSTANDꢁBYꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀOFFꢀ  
ꢀDeviationꢀalarmꢀ  
ꢀProcessꢀvariableꢀconnectionꢀ  
ꢀRemoteꢀsetpointꢀconnectionꢀ  
ꢀReferenceꢀvariableꢀconnectionꢀ  
ꢀProportionalꢀbandꢀconnectionꢀ  
ꢀOFFꢀmodeꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀSTANDꢁBYꢀmodeꢀlogicꢀcontrolꢀ  
connectionꢀ  
ꢀFPꢀꢀ  
40ꢀꢀByteꢀꢀ  
41ꢀꢀByteꢀꢀ  
42ꢀꢀByteꢀꢀ  
43ꢀꢀByteꢀꢀ  
44ꢀꢀByteꢀꢀ  
65ꢀ  
66ꢀ  
67ꢀ  
68ꢀ  
69ꢀ  
70ꢀ  
71ꢀ  
45ꢀꢀByteꢀꢀ  
46ꢀꢀByteꢀꢀ  
47ꢀꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀSB2@ꢀꢀ  
ꢀRA2@ꢀꢀ  
ꢀEF2@ꢀꢀ  
ꢀReverseꢀactionꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀExternalꢀforcingꢀlogicꢀcontrolꢀ  
connectionꢀ  
72ꢀ  
73ꢀ  
48ꢀꢀByteꢀꢀ  
49ꢀꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀTYPE2ꢀꢀ  
ꢀLS2ꢀꢀ  
ꢀPB2ꢀꢀ  
ꢀTI2ꢀꢀ  
ꢀTD2ꢀꢀ  
ꢀHL2ꢀꢀ  
ꢀLL2ꢀꢀ  
ꢀLL2ꢀꢀ  
ꢀBS2ꢀꢀ  
ꢀControllerꢀtypeꢀ  
ꢀLocalꢀsetpointꢀ  
ꢀProportionalꢀbandꢀ  
ꢀResetꢀactionꢀ  
74ꢀꢀ4Aꢀꢀ  
75ꢀꢀ4Bꢀꢀ  
76ꢀꢀ4Cꢀꢀ  
77ꢀꢀ4Dꢀꢀ  
78ꢀꢀ4Eꢀꢀ  
78ꢀꢀ4Eꢀꢀ  
79ꢀꢀ4Fꢀꢀ  
80ꢀ  
81ꢀ  
82ꢀ  
83ꢀ  
84ꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀRateꢀactionꢀ  
ꢀUpperꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀSTANDꢁBYꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀOFFꢀ  
ꢀDeviationꢀalarmꢀ  
ꢀProcessꢀvariableꢀconnectionꢀ  
ꢀRemoteꢀsetpointꢀconnectionꢀ  
ꢀReferenceꢀvariableꢀconnectionꢀ  
ꢀProportionalꢀbandꢀconnectionꢀ  
ꢀOFFꢀmodeꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀSTANDꢁBYꢀmodeꢀlogicꢀcontrolꢀ  
connectionꢀ  
50ꢀꢀFPꢀꢀ  
51ꢀꢀFPꢀꢀ  
52ꢀꢀByteꢀꢀ  
53ꢀꢀByteꢀꢀ  
54ꢀꢀByteꢀꢀ  
55ꢀꢀByteꢀꢀ  
56ꢀꢀByteꢀꢀ  
ꢀBO2ꢀꢀ  
ꢀAD2ꢀꢀ  
ꢀPV3@ꢀꢀ  
ꢀRS3@ꢀꢀ  
ꢀRV3@ꢀꢀ  
ꢀPB3@ꢀꢀ  
ꢀOF3@ꢀꢀ  
85ꢀ  
86ꢀ  
87ꢀ  
88ꢀ  
57ꢀꢀByteꢀꢀ  
58ꢀꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀSB3@ꢀꢀ  
ꢀRA3@ꢀꢀ  
ꢀReverseꢀactionꢀlogicꢀcontrolꢀconnectionꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 35 of 51  
PAGE 0  
Johnson  
Tag  
Item  
DEC  
Item  
HEX  
Signal Condition Read/Write  
Description  
ꢀExternalꢀforcingꢀlogicꢀcontrolꢀ  
connectionꢀ  
89ꢀ  
59ꢀꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀEF3@ꢀꢀ  
90ꢀꢀ5Aꢀꢀ  
91ꢀꢀ5Bꢀꢀ  
92ꢀꢀ5Cꢀꢀ  
93ꢀꢀ5Dꢀꢀ  
94ꢀꢀ5Eꢀꢀ  
95ꢀꢀ5Fꢀꢀ  
96ꢀ  
97ꢀ  
98ꢀ  
99ꢀ  
100ꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀTYPE3ꢀꢀ  
ꢀLS3ꢀꢀ  
ꢀPB3ꢀꢀ  
ꢀTI3ꢀꢀ  
ꢀTD3ꢀꢀ  
ꢀHL3ꢀꢀ  
ꢀLL3ꢀꢀ  
ꢀBS3ꢀꢀ  
ꢀBO3ꢀꢀ  
ꢀAD3ꢀꢀ  
ꢀPV4@ꢀꢀ  
ꢀRS4@ꢀꢀ  
ꢀRV4@ꢀꢀ  
ꢀPB4@ꢀꢀ  
ꢀOF4@ꢀꢀ  
ꢀControllerꢀtypeꢀ  
ꢀLocalꢀsetpointꢀ  
ꢀProportionalꢀbandꢀ  
ꢀResetꢀactionꢀ  
ꢀRateꢀactionꢀ  
ꢀUpperꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀSTANDꢁBYꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀOFFꢀ  
ꢀDeviationꢀalarmꢀ  
ꢀProcessꢀvariableꢀconnectionꢀ  
ꢀRemoteꢀsetpointꢀconnectionꢀ  
ꢀReferenceꢀvariableꢀconnectionꢀ  
ꢀProportionalꢀbandꢀconnectionꢀ  
ꢀOFFꢀmodeꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀSTANDꢁBYꢀmodeꢀlogicꢀcontrolꢀ  
connectionꢀ  
60ꢀꢀFPꢀꢀ  
61ꢀꢀFPꢀꢀ  
62ꢀꢀFPꢀꢀ  
63ꢀꢀFPꢀꢀ  
64ꢀꢀByteꢀꢀ  
65ꢀꢀByteꢀꢀ  
66ꢀꢀByteꢀꢀ  
67ꢀꢀByteꢀꢀ  
68ꢀꢀByteꢀꢀ  
101ꢀ  
102ꢀ  
103ꢀ  
104ꢀ  
105ꢀ  
69ꢀꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀSB4@ꢀꢀ  
ꢀRA4@ꢀꢀ  
ꢀEF4@ꢀꢀ  
106ꢀꢀ6Aꢀꢀ  
107ꢀꢀ6Bꢀꢀ  
ꢀReverseꢀactionꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀExternalꢀforcingꢀlogicꢀcontrolꢀ  
connectionꢀ  
ꢀByteꢀꢀ  
108ꢀꢀ6Cꢀꢀ  
109ꢀꢀ6Dꢀꢀ  
110ꢀꢀ6Eꢀꢀ  
111ꢀꢀ6Fꢀꢀ  
112ꢀ  
113ꢀ  
114ꢀ  
115ꢀ  
116ꢀ  
117ꢀ  
118ꢀ  
119ꢀ  
120ꢀ  
121ꢀ  
122ꢀꢀ7Aꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀTYPE4ꢀꢀ  
ꢀLS4ꢀꢀ  
ꢀPB4ꢀꢀ  
ꢀTI4ꢀꢀ  
ꢀTD4ꢀꢀ  
ꢀHL4ꢀꢀ  
ꢀLL4ꢀꢀ  
ꢀBS4ꢀꢀ  
ꢀBO4ꢀꢀ  
ꢀAD4ꢀꢀ  
ꢀPV5@ꢀꢀ  
ꢀRS5@ꢀꢀ  
ꢀRV5@ꢀꢀ  
ꢀPB5@ꢀꢀ  
ꢀOF5@ꢀꢀ  
ꢀControllerꢀtypeꢀ  
ꢀLocalꢀsetpointꢀ  
ꢀProportionalꢀbandꢀ  
ꢀResetꢀactionꢀ  
ꢀFPꢀꢀ  
70ꢀꢀFPꢀꢀ  
71ꢀꢀFPꢀꢀ  
72ꢀꢀFPꢀꢀ  
73ꢀꢀFPꢀꢀ  
74ꢀꢀFPꢀꢀ  
75ꢀꢀFPꢀꢀ  
76ꢀꢀByteꢀꢀ  
77ꢀꢀByteꢀꢀ  
78ꢀꢀByteꢀꢀ  
79ꢀꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀRateꢀactionꢀ  
ꢀUpperꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀSTANDꢁBYꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀOFFꢀ  
ꢀDeviationꢀalarmꢀ  
ꢀProcessꢀvariableꢀconnectionꢀ  
ꢀRemoteꢀsetpointꢀconnectionꢀ  
ꢀReferenceꢀvariableꢀconnectionꢀ  
ꢀProportionalꢀbandꢀconnectionꢀ  
ꢀOFFꢀmodeꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀSTANDꢁBYꢀmodeꢀlogicꢀcontrolꢀ  
connectionꢀ  
123ꢀꢀ7Bꢀꢀ  
124ꢀꢀ7Cꢀꢀ  
125ꢀꢀ7Dꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀSB5@ꢀꢀ  
ꢀRA5@ꢀꢀ  
ꢀEF5@ꢀꢀ  
ꢀReverseꢀactionꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀExternalꢀforcingꢀlogicꢀcontrolꢀ  
connectionꢀ  
126ꢀꢀ7Eꢀꢀ  
127ꢀꢀ7Fꢀꢀ  
128ꢀ  
129ꢀ  
130ꢀ  
131ꢀ  
132ꢀ  
133ꢀ  
134ꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀTYPE5ꢀꢀ  
ꢀLS5ꢀꢀ  
ꢀPB5ꢀꢀ  
ꢀTI5ꢀꢀ  
ꢀTD5ꢀꢀ  
ꢀHL5ꢀꢀ  
ꢀLL5ꢀꢀ  
ꢀControllerꢀtypeꢀ  
ꢀLocalꢀsetpointꢀ  
ꢀProportionalꢀbandꢀ  
ꢀResetꢀactionꢀ  
80ꢀꢀFPꢀꢀ  
81ꢀꢀFPꢀꢀ  
82ꢀꢀFPꢀꢀ  
83ꢀꢀFPꢀꢀ  
84ꢀꢀFPꢀꢀ  
85ꢀꢀFPꢀꢀ  
86ꢀꢀFPꢀꢀ  
ꢀRateꢀactionꢀ  
ꢀUpperꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀSTANDꢁBYꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀOFFꢀ  
ꢀBS5ꢀꢀ  
ꢀBO5ꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 36 of 51  
PAGE 0  
Johnson  
Tag  
Item  
DEC  
Item  
HEX  
Signal Condition Read/Write  
Description  
135ꢀ  
136ꢀ  
137ꢀ  
138ꢀꢀ8Aꢀꢀ  
139ꢀꢀ8Bꢀꢀ  
140ꢀꢀ8Cꢀꢀ  
87ꢀꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀAD5ꢀꢀ  
ꢀDeviationꢀalarmꢀ  
88ꢀꢀByteꢀꢀ  
89ꢀꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀPV6@ꢀꢀ  
ꢀRS6@ꢀꢀ  
ꢀRV6@ꢀꢀ  
ꢀPB6@ꢀꢀ  
ꢀOF6@ꢀꢀ  
ꢀProcessꢀvariableꢀconnectionꢀ  
ꢀRemoteꢀsetpointꢀconnectionꢀ  
ꢀReferenceꢀvariableꢀconnectionꢀ  
ꢀProportionalꢀbandꢀconnectionꢀ  
ꢀOFFꢀmodeꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀSTANDꢁBYꢀmodeꢀlogicꢀcontrolꢀ  
connectionꢀ  
ꢀReverseꢀactionꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀExternalꢀforcingꢀlogicꢀcontrolꢀ  
connectionꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
141ꢀꢀ8Dꢀꢀ  
142ꢀꢀ8Eꢀꢀ  
143ꢀꢀ8Fꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀSB6@ꢀꢀ  
ꢀRA6@ꢀꢀ  
ꢀEF6@ꢀꢀ  
144ꢀ  
145ꢀ  
146ꢀ  
147ꢀ  
148ꢀ  
149ꢀ  
150ꢀ  
151ꢀ  
90ꢀꢀByteꢀꢀ  
91ꢀꢀFPꢀꢀ  
92ꢀꢀFPꢀꢀ  
93ꢀꢀFPꢀꢀ  
94ꢀꢀFPꢀꢀ  
95ꢀꢀFPꢀꢀ  
96ꢀꢀFPꢀꢀ  
97ꢀꢀFPꢀꢀ  
98ꢀꢀFPꢀꢀ  
99ꢀꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀTYPE6ꢀꢀ  
ꢀLS6ꢀꢀ  
ꢀPB6ꢀꢀ  
ꢀTI6ꢀꢀ  
ꢀTD6ꢀꢀ  
ꢀHL6ꢀꢀ  
ꢀLL6ꢀꢀ  
ꢀBS6ꢀꢀ  
ꢀBO6ꢀꢀ  
ꢀAD6ꢀꢀ  
ꢀPV7@ꢀꢀ  
ꢀRS7@ꢀꢀ  
ꢀRV7@ꢀꢀ  
ꢀPB7@ꢀꢀ  
ꢀOF7@ꢀꢀ  
ꢀControllerꢀtypeꢀ  
ꢀLocalꢀsetpointꢀ  
ꢀProportionalꢀbandꢀ  
ꢀResetꢀactionꢀ  
ꢀRateꢀactionꢀ  
ꢀUpperꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀSTANDꢁBYꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀOFFꢀ  
ꢀDeviationꢀalarmꢀ  
ꢀProcessꢀvariableꢀconnectionꢀ  
ꢀRemoteꢀsetpointꢀconnectionꢀ  
ꢀReferenceꢀvariableꢀconnectionꢀ  
ꢀProportionalꢀbandꢀconnectionꢀ  
ꢀOFFꢀmodeꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀSTANDꢁBYꢀmodeꢀlogicꢀcontrolꢀ  
connectionꢀ  
152ꢀ  
153ꢀ  
154ꢀꢀ9Aꢀꢀ  
155ꢀꢀ9Bꢀꢀ  
156ꢀꢀ9Cꢀꢀ  
157ꢀꢀ9Dꢀꢀ  
158ꢀꢀ9Eꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
159ꢀꢀ9Fꢀꢀ  
160ꢀꢀA0ꢀꢀ  
161ꢀꢀA1ꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀSB7@ꢀꢀ  
ꢀRA7@ꢀꢀ  
ꢀEF7@ꢀꢀ  
ꢀReverseꢀactionꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀExternalꢀforcingꢀlogicꢀcontrolꢀ  
connectionꢀ  
162ꢀꢀA2ꢀꢀ  
163ꢀꢀA3ꢀꢀ  
164ꢀꢀA4ꢀꢀ  
165ꢀꢀA5ꢀꢀ  
166ꢀꢀA6ꢀꢀ  
167ꢀꢀA7ꢀꢀ  
168ꢀꢀA8ꢀꢀ  
169ꢀꢀA9ꢀꢀ  
170ꢀꢀAAꢀꢀ  
171ꢀꢀABꢀꢀ  
172ꢀꢀACꢀꢀ  
173ꢀꢀADꢀꢀ  
174ꢀꢀAEꢀꢀ  
175ꢀꢀAFꢀꢀ  
176ꢀꢀB0ꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀTYPE7ꢀꢀ  
ꢀLS7ꢀꢀ  
ꢀPB7ꢀꢀ  
ꢀTI7ꢀꢀ  
ꢀTD7ꢀꢀ  
ꢀHL7ꢀꢀ  
ꢀLL7ꢀꢀ  
ꢀBS7ꢀꢀ  
ꢀBO7ꢀꢀ  
ꢀAD7ꢀꢀ  
ꢀPV8@ꢀꢀ  
ꢀRS8@ꢀꢀ  
ꢀRV8@ꢀꢀ  
ꢀPB8@ꢀꢀ  
ꢀOF8@ꢀꢀ  
ꢀControllerꢀtypeꢀ  
ꢀLocalꢀsetpointꢀ  
ꢀProportionalꢀbandꢀ  
ꢀResetꢀactionꢀ  
ꢀRateꢀactionꢀ  
ꢀUpperꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀSTANDꢁBYꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀOFFꢀ  
ꢀDeviationꢀalarmꢀ  
ꢀProcessꢀvariableꢀconnectionꢀ  
ꢀRemoteꢀsetpointꢀconnectionꢀ  
ꢀReferenceꢀvariableꢀconnectionꢀ  
ꢀProportionalꢀbandꢀconnectionꢀ  
ꢀOFFꢀmodeꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀSTANDꢁBYꢀmodeꢀlogicꢀcontrolꢀ  
connectionꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
177ꢀꢀB1ꢀꢀ  
178ꢀꢀB2ꢀꢀ  
179ꢀꢀB3ꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀSB8@ꢀꢀ  
ꢀRA8@ꢀꢀ  
ꢀEF8@ꢀꢀ  
ꢀReverseꢀactionꢀlogicꢀcontrolꢀconnectionꢀ  
ꢀExternalꢀforcingꢀlogicꢀcontrolꢀ  
connectionꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 37 of 51  
PAGE 0  
Johnson  
Tag  
Item  
DEC  
Item  
HEX  
Signal Condition Read/Write  
Description  
180ꢀꢀB4ꢀꢀ  
181ꢀꢀB5ꢀꢀ  
182ꢀꢀB6ꢀꢀ  
183ꢀꢀB7ꢀꢀ  
184ꢀꢀB8ꢀꢀ  
185ꢀꢀB9ꢀꢀ  
186ꢀꢀBAꢀꢀ  
187ꢀꢀBBꢀꢀ  
188ꢀꢀBCꢀꢀ  
189ꢀꢀBDꢀꢀ  
190ꢀꢀBEꢀꢀ  
191ꢀꢀBFꢀꢀ  
192ꢀꢀC0ꢀꢀ  
193ꢀꢀC1ꢀꢀ  
194ꢀꢀC2ꢀꢀ  
195ꢀꢀC3ꢀꢀ  
196ꢀꢀC4ꢀꢀ  
197ꢀꢀC5ꢀꢀ  
198ꢀꢀC6ꢀꢀ  
199ꢀꢀC7ꢀꢀ  
200ꢀꢀC8ꢀꢀ  
201ꢀꢀC9ꢀꢀ  
202ꢀꢀCAꢀꢀ  
203ꢀꢀCBꢀꢀ  
204ꢀꢀCCꢀꢀ  
205ꢀꢀCDꢀꢀ  
206ꢀꢀCEꢀꢀ  
207ꢀꢀCFꢀꢀ  
208ꢀꢀD0ꢀꢀ  
209ꢀꢀD1ꢀꢀ  
210ꢀꢀD2ꢀꢀ  
211ꢀꢀD3ꢀꢀ  
212ꢀꢀD4ꢀꢀ  
213ꢀꢀD5ꢀꢀ  
214ꢀꢀD6ꢀꢀ  
215ꢀꢀD7ꢀꢀ  
216ꢀꢀD8ꢀꢀ  
217ꢀꢀD9ꢀꢀ  
218ꢀꢀDAꢀꢀ  
219ꢀꢀDBꢀꢀ  
220ꢀꢀDCꢀꢀ  
221ꢀꢀDDꢀꢀ  
222ꢀꢀDEꢀꢀ  
223ꢀꢀDFꢀꢀ  
224ꢀꢀE0ꢀꢀ  
225ꢀꢀE1ꢀꢀ  
226ꢀꢀE2ꢀꢀ  
227ꢀꢀE3ꢀꢀ  
228ꢀꢀE4ꢀꢀ  
229ꢀꢀE5ꢀꢀ  
230ꢀꢀE6ꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀTYPE8ꢀꢀ  
ꢀLS8ꢀꢀ  
ꢀPB8ꢀꢀ  
ꢀTI8ꢀꢀ  
ꢀTD8ꢀꢀ  
ꢀHL8ꢀꢀ  
ꢀLL8ꢀꢀ  
ꢀBS8ꢀꢀ  
ꢀBO8ꢀꢀ  
ꢀAD8ꢀꢀ  
ꢀIR1ꢀꢀ  
ꢀControllerꢀtypeꢀ  
ꢀLocalꢀsetpointꢀ  
ꢀProportionalꢀbandꢀ  
ꢀResetꢀactionꢀ  
ꢀRateꢀactionꢀ  
ꢀUpperꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀLowerꢀlimitꢀofꢀtheꢀcontrolꢀoutputꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀSTANDꢁBYꢀ  
ꢀChangeꢀofꢀsetpointꢀduringꢀOFFꢀ  
ꢀDeviationꢀalarmꢀ  
ꢀRangeꢀanalogꢀinputꢀ1ꢀ  
ꢀHighꢀalarmꢀinputꢀ1ꢀ  
ꢀLowꢀalarmꢀinputꢀ1ꢀ  
ꢀFilterꢀtimeꢀinputꢀ1ꢀ  
ꢀRangeꢀanalogꢀinputꢀ2ꢀ  
ꢀHighꢀalarmꢀinputꢀ2ꢀ  
ꢀLowꢀalarmꢀinputꢀ2ꢀ  
ꢀFilterꢀtimeꢀinputꢀ2ꢀ  
ꢀRangeꢀanalogꢀinputꢀ3ꢀ  
ꢀHighꢀalarmꢀinputꢀ3ꢀ  
ꢀLowꢀalarmꢀinputꢀ3ꢀ  
ꢀFilterꢀtimeꢀinputꢀ3ꢀ  
ꢀRangeꢀanalogꢀinputꢀ4ꢀ  
ꢀHighꢀalarmꢀinputꢀ4ꢀ  
ꢀLowꢀalarmꢀinputꢀ4ꢀ  
ꢀFilterꢀtimeꢀinputꢀ4ꢀ  
ꢀRangeꢀanalogꢀinputꢀ5ꢀ  
ꢀHighꢀalarmꢀinputꢀ5ꢀ  
ꢀLowꢀalarmꢀinputꢀ5ꢀ  
ꢀFilterꢀtimeꢀinputꢀ5ꢀ  
ꢀRangeꢀanalogꢀinputꢀ6ꢀ  
ꢀHighꢀalarmꢀinputꢀ6ꢀ  
ꢀLowꢀalarmꢀinputꢀ6ꢀ  
ꢀFilterꢀtimeꢀinputꢀ6ꢀ  
ꢀRangeꢀanalogꢀinputꢀ7ꢀ  
ꢀHighꢀalarmꢀinputꢀ7ꢀ  
ꢀLowꢀalarmꢀinputꢀ7ꢀ  
ꢀFilterꢀtimeꢀinputꢀ7ꢀ  
ꢀRangeꢀanalogꢀinputꢀ8ꢀ  
ꢀHighꢀalarmꢀinputꢀ8ꢀ  
ꢀHA1ꢀꢀ  
ꢀLA1ꢀꢀ  
ꢀFI1ꢀꢀ  
ꢀIR2ꢀꢀ  
ꢀHA2ꢀꢀ  
ꢀLA2ꢀꢀ  
ꢀFI2ꢀꢀ  
ꢀIR3ꢀꢀ  
ꢀHA3ꢀꢀ  
ꢀLA3ꢀꢀ  
ꢀFI3ꢀꢀ  
ꢀIR4ꢀꢀ  
ꢀHA4ꢀꢀ  
ꢀLA4ꢀꢀ  
ꢀFI4ꢀꢀ  
ꢀIR5ꢀꢀ  
ꢀHA5ꢀꢀ  
ꢀLA5ꢀꢀ  
ꢀFI5ꢀꢀ  
ꢀIR6ꢀꢀ  
ꢀHA6ꢀꢀ  
ꢀLA6ꢀꢀ  
ꢀFI6ꢀꢀ  
ꢀIR7ꢀꢀ  
ꢀHA7ꢀꢀ  
ꢀLA7ꢀꢀ  
ꢀFI7ꢀꢀ  
ꢀIR8ꢀꢀ  
ꢀHA8ꢀꢀ  
ꢀLA8ꢀꢀ  
ꢀFI8ꢀꢀ  
ꢀLowꢀalarmꢀinputꢀ8ꢀ  
ꢀFilterꢀtimeꢀinputꢀ8ꢀ  
ꢀOH1ꢀꢀ  
ꢀOL1ꢀꢀ  
ꢀOMS1ꢀꢀ  
ꢀOH2ꢀꢀ  
ꢀOL2ꢀꢀ  
ꢀOMS2ꢀꢀ  
ꢀOH3ꢀꢀ  
ꢀOL3ꢀꢀ  
ꢀOMS3ꢀꢀ  
ꢀOutputꢀ1ꢀhighꢀrangeꢀ  
ꢀOutput1ꢀlowꢀrangeꢀ  
ꢀSourceꢀofꢀanalogꢀoutputꢀmoduleꢀ1ꢀ  
ꢀOutputꢀ2ꢀhighꢀrangeꢀ  
ꢀOutputꢀ2ꢀlowꢀrangeꢀ  
ꢀSourceꢀofꢀanalogꢀoutputꢀmoduleꢀ2ꢀ  
ꢀOutputꢀOUTA1ꢀhighꢀrangeꢀ  
ꢀOutputꢀOUTA1ꢀlowꢀrangeꢀ  
ꢀSourceꢀofꢀlogicꢀoutputꢀmoduleꢀOUTAꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 38 of 51  
PAGE 0  
Johnson  
Tag  
Item  
DEC  
Item  
HEX  
Signal Condition Read/Write  
Description  
231ꢀꢀE7ꢀꢀ  
232ꢀꢀE8ꢀꢀ  
233ꢀꢀE9ꢀꢀ  
234ꢀꢀEAꢀꢀ  
235ꢀꢀEBꢀꢀ  
236ꢀꢀECꢀꢀ  
237ꢀꢀEDꢀꢀ  
238ꢀꢀEEꢀꢀ  
239ꢀꢀEFꢀꢀ  
240ꢀꢀF0ꢀꢀ  
241ꢀꢀF1ꢀꢀ  
242ꢀꢀF2ꢀꢀ  
243ꢀꢀF3ꢀꢀ  
244ꢀꢀF4ꢀꢀ  
245ꢀꢀF5ꢀꢀ  
246ꢀꢀF6ꢀꢀ  
247ꢀꢀF7ꢀꢀ  
248ꢀꢀF8ꢀꢀ  
249ꢀꢀF9ꢀꢀ  
250ꢀꢀFAꢀꢀ  
251ꢀꢀFBꢀꢀ  
252ꢀꢀFCꢀꢀ  
253ꢀꢀFDꢀꢀ  
254ꢀꢀFEꢀꢀ  
255ꢀꢀFFꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀOMS4ꢀꢀ  
ꢀOMTY1ꢀꢀ  
ꢀFST1ꢀꢀ  
ꢀDB1ꢀꢀ  
ꢀOH5ꢀꢀ  
ꢀOL5ꢀꢀ  
ꢀOMS5ꢀꢀ  
ꢀOMS6ꢀꢀ  
ꢀOMTY2ꢀꢀ  
ꢀFST2ꢀꢀ  
ꢀDB2ꢀꢀ  
ꢀSourceꢀofꢀlogicꢀoutputꢀmoduleꢀOUTBꢀ  
ꢀOutputꢀmoduleꢀtypeꢀ  
ꢀPAT/DATꢀoutputꢀ1ꢀtimingꢀ  
ꢀDeadꢀbandꢀPATꢀoutputꢀ1ꢀ  
ꢀOutputꢀOUTA2ꢀhighꢀrangeꢀ  
ꢀOutputꢀOUTA2ꢀlowꢀrangeꢀ  
ꢀSourceꢀofꢀlogicꢀoutputꢀmoduleꢀOUTAꢀ  
ꢀSourceꢀofꢀlogicꢀoutputꢀmoduleꢀOUTBꢀ  
ꢀOutputꢀmoduleꢀtypeꢀ  
ꢀPAT/DATꢀoutputꢀ2ꢀtimingꢀ  
ꢀDeadꢀbandꢀPATꢀoutputꢀ2ꢀ  
ꢀOutputꢀOUTA3ꢀhighꢀrangeꢀ  
ꢀOutputꢀOUTA3ꢀlowꢀrangeꢀ  
ꢀSourceꢀofꢀlogicꢀoutputꢀmoduleꢀOUTAꢀ  
ꢀSourceꢀofꢀlogicꢀoutputꢀmoduleꢀOUTBꢀ  
ꢀOutputꢀmoduleꢀtypeꢀ  
ꢀPAT/DATꢀoutputꢀ3ꢀtimingꢀ  
ꢀDeadꢀbandꢀPATꢀoutputꢀ3ꢀ  
ꢀSymmetryꢀbandꢀcontrollerꢀmoduleꢀ5ꢀ  
ꢀSymmetryꢀbandꢀcontrollerꢀmoduleꢀ6ꢀ  
ꢀAlarmꢀdisableꢀconditionꢀsourceꢀ  
ꢀDCꢀtypeꢀsettingsꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀOH7ꢀꢀ  
ꢀOL7ꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀOMS7ꢀꢀ  
ꢀOMS8ꢀꢀ  
ꢀOMty3ꢀꢀ  
ꢀFST3ꢀꢀ  
ꢀDB3ꢀꢀ  
ꢀSB1ꢀꢀ  
ꢀSB2ꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀByteꢀꢀ  
ꢀFPꢀꢀ  
ꢀALDISꢀꢀ  
ꢀRCTY1ꢀꢀ  
ꢀALGTꢀꢀ  
ꢀCOS1ꢀꢀ  
ꢀCOS2ꢀꢀ  
ꢀStandardꢀalgorithmꢀtypeꢀ  
ꢀSpareꢀconstantꢀ  
ꢀSpareꢀconstantꢀ  
ꢀFPꢀꢀ  
PAGE 1ꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description Relative Item  
0ꢀ  
1ꢀ  
2ꢀ  
3ꢀ  
4ꢀ  
5ꢀ  
6ꢀ  
7ꢀ  
0ꢀꢀFPꢀꢀ  
1ꢀꢀFPꢀꢀ  
2ꢀꢀFPꢀꢀ  
3ꢀꢀFPꢀꢀ  
4ꢀꢀFPꢀꢀ  
5ꢀꢀFPꢀꢀ  
6ꢀꢀFPꢀꢀ  
7ꢀꢀFPꢀꢀ  
8ꢀꢀFPꢀꢀ  
9ꢀꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀHR1ꢀꢀ  
ꢀLR1ꢀꢀ  
ꢀHR2ꢀꢀ  
ꢀLR2ꢀꢀ  
ꢀHR3ꢀꢀ  
ꢀLR3ꢀꢀ  
ꢀHR4ꢀꢀ  
ꢀLR4ꢀꢀ  
ꢀHR5ꢀꢀ  
ꢀLR5ꢀꢀ  
ꢀHR6ꢀꢀ  
ꢀLR6ꢀꢀ  
ꢀHR7ꢀꢀ  
ꢀLR7ꢀꢀ  
ꢀHR8ꢀꢀ  
ꢀLR8ꢀꢀ  
ꢀOM%1ꢀꢀ  
ꢀOM%2ꢀꢀ  
ꢀOM%3ꢀꢀ  
ꢀOM%4ꢀꢀ  
ꢀOM%5ꢀꢀ  
ꢀOM%6ꢀꢀ  
ꢀOM%7ꢀꢀ  
ꢀOM%8ꢀꢀ  
ꢀHighꢀrangeꢀanalogꢀinputꢀ1ꢀ  
ꢀLowꢀrangeꢀanalogꢀinputꢀ1ꢀ  
ꢀHighꢀrangeꢀanalogꢀinputꢀ2ꢀ  
ꢀLowꢀrangeꢀanalogꢀinputꢀ2ꢀ  
ꢀHighꢀrangeꢀanalogꢀinputꢀ3ꢀ  
ꢀLowꢀrangeꢀanalogꢀinputꢀ3ꢀ  
ꢀHighꢀrangeꢀanalogꢀinputꢀ4ꢀ  
ꢀLowꢀrangeꢀanalogꢀinputꢀ4ꢀ  
ꢀHighꢀrangeꢀanalogꢀinputꢀ5ꢀ  
ꢀLowꢀrangeꢀanalogꢀinputꢀ5ꢀ  
ꢀHighꢀrangeꢀanalogꢀinputꢀ6ꢀ  
ꢀLowꢀrangeꢀanalogꢀinputꢀ6ꢀ  
ꢀHighꢀrangeꢀanalogꢀinputꢀ7ꢀ  
ꢀLowꢀrangeꢀanalogꢀinputꢀ7ꢀ  
ꢀHighꢀrangeꢀanalogꢀinputꢀ8ꢀ  
ꢀLowꢀrangeꢀanalogꢀinputꢀ8ꢀ  
ꢀOutputꢀ%ꢀOutputꢀmoduleꢀ1ꢀ  
ꢀOutputꢀ%ꢀOutputꢀmoduleꢀ2ꢀ  
ꢀOutputꢀ%ꢀOutputꢀmoduleꢀ3ꢀ  
ꢀOutputꢀ%ꢀOutputꢀmoduleꢀ4ꢀ  
ꢀOutputꢀ%ꢀOutputꢀmoduleꢀ5ꢀ  
ꢀOutputꢀ%ꢀOutputꢀmoduleꢀ6ꢀ  
ꢀOutputꢀ%ꢀOutputꢀmoduleꢀ7ꢀ  
ꢀOutputꢀ%ꢀOutputꢀmoduleꢀ8ꢀ  
8ꢀ  
9ꢀ  
10ꢀꢀAꢀꢀ  
11ꢀꢀBꢀꢀ  
12ꢀꢀCꢀꢀ  
13ꢀꢀDꢀꢀ  
14ꢀꢀEꢀꢀ  
15ꢀꢀFꢀꢀ  
16ꢀ  
17ꢀ  
18ꢀ  
19ꢀ  
20ꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
10ꢀꢀFPꢀꢀ  
11ꢀꢀFPꢀꢀ  
12ꢀꢀFPꢀꢀ  
13ꢀꢀFPꢀꢀ  
14ꢀꢀFPꢀꢀ  
15ꢀꢀFPꢀꢀ  
16ꢀꢀFPꢀꢀ  
17ꢀꢀFPꢀꢀ  
21ꢀ  
22ꢀ  
23ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 39 of 51  
Optimal start / stop moduleꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
0ꢀꢀ  
1ꢀꢀ  
2ꢀꢀ  
3ꢀꢀ  
4ꢀꢀ  
5ꢀꢀ  
6ꢀꢀ  
7ꢀꢀ  
ꢀByteꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀWordꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀWriteꢀꢀ  
ꢀOSOPTꢀꢀ  
ꢀOSZT@ꢀꢀ  
ꢀOSOT@ꢀꢀ  
ꢀOSSP@ꢀꢀ  
ꢀOSOB@ꢀꢀ  
ꢀOSDI@ꢀꢀ  
ꢀOSDA@ꢀꢀ  
ꢀOSTS@ꢀꢀ  
ꢀOSNX@ꢀꢀ  
ꢀOSTIM@ꢀꢀ  
ꢀOSPURGEꢀꢀ  
ꢀOSMAXSTꢀꢀ  
ꢀOSMAXSOꢀꢀ  
ꢀOSBHKꢀꢀ  
ꢀOSBCKꢀꢀ  
ꢀOSSBHKꢀꢀ  
ꢀOSSBCKꢀꢀ  
ꢀOSFWꢀꢀ  
Moduleꢀoptionsꢀ  
Zoneꢀtemperatureꢀconnectionꢀ  
Outdoorꢀtemperatureꢀconnectionꢀ  
Zoneꢀtemperatureꢀsetpointꢀconnectionꢀ  
Offꢀsetpointꢀbiasꢀconnectionꢀ  
Disableꢀmoduleꢀconnectionꢀ  
Disableꢀadaptiveꢀactionꢀconnectionꢀ  
Connectionꢀatꢀtimeꢀscheduleꢀoutputꢀ  
Connectionꢀatꢀnextꢀoutputꢀ  
8ꢀꢀ  
9ꢀꢀ  
Connectionꢀatꢀtimeꢀtoꢀnextꢀoutputꢀ  
Minimumꢀcoolꢀ/ꢀheatꢀtimeꢀ(min)ꢀ  
Maximumꢀstartꢀupꢀtimeꢀ(min)ꢀ  
Maximumꢀshutꢀdownꢀtimeꢀ(min)ꢀ  
Startꢀmodeꢀbuildingꢀheatingꢀfactorꢀ  
Startꢀmodeꢀbuildingꢀcoolingꢀfactorꢀ  
Stopꢀmodeꢀbuildingꢀheatingꢀfactorꢀ  
Stopꢀmodeꢀbuildingꢀcoolingꢀfactorꢀ  
Percentageꢀadaptiveꢀcontrolꢀ(filterꢀweight)ꢀ  
Outdoorꢀheatingꢀdesignꢀtemperatureꢀ  
Outdoorꢀcoolingꢀdesignꢀtemperatureꢀ  
Controlꢀrangeꢀ  
10ꢀꢀ  
11ꢀꢀ  
12ꢀꢀ  
13ꢀꢀ  
14ꢀꢀ  
15ꢀꢀ  
16ꢀꢀ  
17ꢀꢀ  
18ꢀꢀ  
19ꢀꢀ  
20ꢀꢀ  
21ꢀꢀ  
22ꢀꢀ  
23ꢀꢀ  
24ꢀꢀ  
ꢀOSHTDꢀꢀ  
ꢀOSCTDꢀꢀ  
ꢀOSCRNGꢀꢀ  
ꢀOSSPꢀꢀ  
ꢀOSOBꢀꢀ  
ꢀOSTIMꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀFPꢀꢀ  
ꢀByteꢀꢀ  
Zoneꢀtemperatureꢀonꢀsetpointꢀ  
Zoneꢀtemperatureꢀoffꢀsetpointꢀ  
Remainingꢀtimeꢀtoꢀnextꢀeventꢀ  
Operatingꢀstatusꢀ  
ꢀOSSTAꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 40 of 51  
Appendix D.3. Metasys TC9100 Memory Map  
Note: The TC9100 is not currently supported by the FieldServer MetasysN2 Driver.  
The information below is for interest and future use only.  
General dynamic Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
0ꢀꢀꢀ  
1ꢀꢀꢀ  
2ꢀꢀꢀ  
3ꢀꢀꢀ  
4ꢀꢀꢀ  
5ꢀꢀꢀ  
6ꢀꢀꢀ  
7ꢀꢀꢀ  
8ꢀꢀꢀ  
9ꢀꢀꢀ  
10ꢀꢀ  
11ꢀꢀ  
12ꢀꢀ  
13ꢀꢀ  
14ꢀꢀ  
15ꢀꢀ  
16ꢀꢀ  
17ꢀꢀ  
18ꢀꢀ  
19ꢀꢀ  
20ꢀꢀ  
21ꢀꢀ  
22ꢀꢀ  
23ꢀꢀ  
24ꢀꢀ  
25ꢀꢀ  
26ꢀꢀ  
27ꢀꢀ  
28ꢀꢀ  
29ꢀꢀ  
30ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
31ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀUNITꢀꢀ  
ꢀꢀAI1ꢀꢀ  
ꢀꢀAI2ꢀꢀ  
ꢀꢀAI3ꢀꢀ  
ꢀꢀAI4ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDeviceꢀmodel.ꢀForꢀTCꢁ9100ꢀalwaysꢀ06hꢀ  
ꢀꢀProcessꢀTemperatureꢀ  
ꢀꢀRemoteꢀTemperatureꢀSetꢀPointꢀBiasꢀ  
ꢀꢀPressureꢀ  
ꢀꢀOverrideꢀInputꢀ  
ꢀꢀSpareꢀ  
ꢀꢀSpareꢀ  
ꢀꢀSpareꢀ  
ꢀꢀSpareꢀ  
ꢀꢀSelectedꢀAnalogꢀInputꢀADCꢀcounterꢀ  
ꢀꢀOutputꢀProgrammableꢀModuleꢀ#1ꢀ  
ꢀꢀOutputꢀProgrammableꢀModuleꢀ#2ꢀ  
ꢀꢀOutputꢀProgrammableꢀModuleꢀ#3ꢀ  
ꢀꢀOutputꢀProgrammableꢀModuleꢀ#4ꢀ  
ꢀꢀOutputꢀProgrammableꢀModuleꢀ#5ꢀ  
ꢀꢀOutputꢀProgrammableꢀModuleꢀ#6ꢀ  
ꢀꢀWorkingꢀSetꢀPointꢀControlꢀModuleꢀ1ꢀ  
ꢀꢀWorkingꢀSetꢀPointꢀControlꢀModuleꢀ2ꢀ  
ꢀꢀWorkingꢀSetꢀPointꢀControlꢀModuleꢀ3ꢀ  
ꢀꢀWorkingꢀSetꢀPointꢀControlꢀModuleꢀ4ꢀ  
ꢀꢀWorkingꢀSetꢀPointꢀControlꢀModuleꢀ5ꢀ  
ꢀꢀWorkingꢀSetꢀPointꢀControlꢀModuleꢀ6ꢀ  
ꢀꢀExternalꢀAnalogꢀInputꢀ1ꢀ  
ꢀꢀExternalꢀAnalogꢀInputꢀ2ꢀ  
ꢀꢀExternalꢀAnalogꢀInputꢀ3ꢀꢀꢀꢀ  
ꢀꢀExternalꢀAnalogꢀInputꢀ4ꢀꢀꢀꢀ  
ꢀꢀAnalogꢀConstantꢀ5ꢀꢀꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀW(2)ꢀꢀ  
ꢀꢀW(3)ꢀꢀ  
ꢀꢀW(4)ꢀꢀ  
ꢀꢀW(5)ꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(7)ꢀꢀ  
ꢀꢀW(8)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀW(10)ꢀꢀ  
ꢀꢀW(11)ꢀꢀ  
ꢀꢀW(12)ꢀꢀ  
ꢀꢀW(13)ꢀꢀ  
ꢀꢀW(14)ꢀꢀ  
ꢀꢀW(15)ꢀꢀ  
ꢀꢀW(16)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀADCꢀꢀ  
ꢀꢀOCM1ꢀꢀ  
ꢀꢀOCM2ꢀꢀ  
ꢀꢀOCM3ꢀꢀ  
ꢀꢀOCM4ꢀꢀ  
ꢀꢀOCM5ꢀꢀ  
ꢀꢀOCM6ꢀꢀ  
ꢀꢀWSP1ꢀꢀ  
ꢀꢀWSP2ꢀꢀ  
ꢀꢀWSP3ꢀꢀ  
ꢀꢀWSP4ꢀꢀ  
ꢀꢀWSP5ꢀꢀ  
ꢀꢀWSP6ꢀꢀ  
ꢀꢀXAI1ꢀꢀ  
ꢀꢀXAI2ꢀꢀ  
ꢀꢀXAI3ꢀꢀ  
ꢀꢀXAI4ꢀꢀ  
ꢀꢀACO5ꢀꢀ  
ꢀꢀACO6ꢀꢀ  
ꢀꢀWACꢀꢀ  
ꢀꢀSACꢀꢀ  
ꢀꢀALRꢀꢀ  
ꢀꢀAIH1ꢀꢀ  
ꢀꢀAIL1ꢀꢀ  
ꢀꢀAIH2ꢀꢀ  
ꢀꢀAIL2ꢀꢀ  
ꢀꢀAIH3ꢀꢀ  
ꢀꢀAIL3ꢀꢀ  
ꢀꢀAIH4ꢀꢀ  
ꢀꢀAIL4ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀAnalogꢀConstantꢀ6ꢀꢀꢀꢀ  
ꢀꢀWinterꢀAuthorityꢀCorrectionꢀꢀꢀ  
ꢀꢀSummerꢀAuthorityꢀCorrectionꢀꢀꢀ  
ꢀꢀAnalogꢀInputsꢀAlarmꢀStatusꢀꢀꢀꢀ  
ꢀꢀAnalogꢀꢀꢀInputꢀꢀꢀ1ꢀHighꢀalarmꢀ  
ꢀꢀAnalogꢀꢀꢀInputꢀꢀꢀ1ꢀHighꢀalarmꢀ  
ꢀꢀAnalogꢀꢀꢀInputꢀꢀꢀ2ꢀHighꢀalarmꢀ  
ꢀꢀAnalogꢀꢀꢀInputꢀꢀꢀ2ꢀLowꢀalarmꢀ  
ꢀꢀAnalogꢀꢀꢀInputꢀꢀꢀ3ꢀHighꢀalarmꢀ  
ꢀꢀAnalogꢀꢀꢀInputꢀꢀꢀ3ꢀLowꢀalarmꢀ  
ꢀꢀAnalogꢀꢀꢀInputꢀꢀꢀ4ꢀHighꢀalarmꢀ  
ꢀꢀAnalogꢀꢀꢀInputꢀꢀꢀ4ꢀLowꢀalarmꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀLogicꢀOutputꢀStatusꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀLOSꢀꢀ  
ꢀꢀDO3ꢀꢀ  
ꢀꢀDO4ꢀꢀ  
ꢀꢀDO5ꢀꢀ  
ꢀꢀTRIACꢀꢀꢀ3ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ4ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ5ꢀꢀONꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 41 of 51  
General dynamic Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
32ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDO6ꢀꢀ  
ꢀꢀDO7ꢀꢀ  
ꢀꢀDO1ꢀꢀ  
ꢀꢀDO2ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀROSꢀꢀ  
ꢀꢀMODSꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTRIACꢀꢀꢀ6ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ7ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ1ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ2ꢀꢀONꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀTC9100ꢀOperationꢀStatusꢀꢀꢀꢀ  
ꢀꢀ00ꢀꢀ=ꢀꢀꢀNightꢀmodeꢀ  
ꢀꢀ01ꢀꢀꢀ=ꢀꢀꢀStandꢁbyꢀmodeꢀ  
ꢀꢀ10ꢀꢀꢀ=ꢀꢀꢀComfortꢀmodeꢀ  
ꢀꢀ11ꢀꢀꢀ=ꢀꢀꢀOFFꢀmodeꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
33ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
34ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
35ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
36ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀMODTꢀꢀ  
ꢀꢀMODAꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTemporaryꢀꢀꢀmodeꢀꢀ  
ꢀꢀAlternateꢀꢀmodeꢀꢀ  
ꢀꢀSupervisoryꢀꢀmodeꢀꢀenabledꢀ  
ꢀꢀWindowꢀꢀꢀopenꢀꢀ  
ꢀꢀOccupancyꢀꢀꢀSenseꢀꢀ  
ꢀꢀAirꢀꢀQualityꢀꢀꢀSenseꢀ  
ꢀꢀOutputsꢀCentralꢀControlꢀꢁꢀEnableꢀꢀꢀꢀ  
ꢀꢀEnableꢀꢀꢀTRIACꢀꢀꢀ3ꢀ  
ꢀꢀEnableꢀꢀꢀTRIACꢀꢀꢀ4ꢀ  
ꢀꢀEnableꢀꢀꢀTRIACꢀꢀꢀ5ꢀ  
ꢀꢀEnableꢀꢀꢀTRIACꢀꢀꢀ6ꢀ  
ꢀꢀEnableꢀꢀꢀTRIACꢀꢀꢀ7ꢀ  
ꢀꢀEnableꢀꢀꢀTRIACꢀꢀꢀ1ꢀ  
ꢀꢀEnableꢀꢀꢀTRIACꢀꢀꢀ2ꢀ  
ꢀꢀOutputsꢀCentralꢀControlꢀꢁꢀSetꢀLevelꢀꢀꢀ  
ꢀꢀTRIACꢀꢀꢀ3ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ4ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ5ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ6ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ7ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ1ꢀꢀONꢀ  
ꢀꢀTRIACꢀꢀꢀ2ꢀꢀONꢀ  
ꢀꢀControlꢀLoopsꢀHoldꢀꢀꢀꢀ  
ꢀꢀLoopꢀꢀ#1ꢀꢀHoldꢀ  
ꢀꢀLoopꢀꢀ#2ꢀꢀHoldꢀꢀ  
ꢀꢀLoopꢀꢀ#3ꢀꢀHoldꢀꢀ  
ꢀꢀLoopꢀꢀ#4ꢀꢀHoldꢀꢀ  
ꢀꢀLoopꢀꢀ#5ꢀꢀHoldꢀꢀ  
ꢀꢀLoopꢀꢀ#6ꢀꢀHoldꢀꢀ  
ꢀꢀComputerꢀmodeꢀControlꢀꢀꢀꢀ  
ꢀꢀLoopꢀꢀ#1ꢀꢀHoldꢀꢀWSPꢀoverrideꢀ  
ꢀꢀLoopꢀꢀ#2ꢀꢀHoldꢀꢀWSPꢀoverrideꢀ  
ꢀꢀLoopꢀꢀ#3ꢀꢀHoldꢀꢀWSPꢀoverrideꢀ  
ꢀꢀLoopꢀꢀ#4ꢀꢀHoldꢀꢀWSPꢀoverrideꢀ  
ꢀꢀLoopꢀꢀ#5ꢀꢀHoldꢀꢀWSPꢀoverrideꢀ  
ꢀꢀLoopꢀꢀ#6ꢀꢀHoldꢀꢀWSPꢀoverrideꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀWINꢀꢀ  
ꢀꢀOCCꢀꢀ  
ꢀꢀAIRQꢀꢀ  
ꢀꢀMSKꢀꢀ  
ꢀꢀDO3Eꢀꢀ  
ꢀꢀDO4Eꢀꢀ  
ꢀꢀDO5Eꢀꢀ  
ꢀꢀDO6Eꢀꢀ  
ꢀꢀDO7Eꢀꢀ  
ꢀꢀDO1Eꢀꢀ  
ꢀꢀDO2Eꢀꢀ  
ꢀꢀODCꢀꢀ  
ꢀꢀDO3Cꢀꢀ  
ꢀꢀDO4Cꢀꢀ  
ꢀꢀDO5Cꢀꢀ  
ꢀꢀDO6Cꢀꢀ  
ꢀꢀDO7Cꢀꢀ  
ꢀꢀDO1Cꢀꢀ  
ꢀꢀDO2Cꢀꢀ  
ꢀꢀHLDꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀHLDꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
37ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSUPꢀꢀ  
ꢀꢀMODCꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSOFFꢀꢀ  
ꢀꢀSTUPꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀMANꢀꢀ  
ꢀꢀSupervisoryꢀModeꢀControlꢀꢀꢀꢀꢀꢀ  
ꢀꢀ00ꢀꢀ=ꢀꢀꢀNightꢀmodeꢀrequestꢀꢀꢀ  
ꢀꢀ01ꢀꢀ=ꢀꢀꢀStandꢁbyꢀmodeꢀrequestꢀꢀ  
ꢀꢀ10ꢀꢀꢀ=ꢀꢀꢀComfortꢀmodeꢀrequestꢀꢀ  
ꢀꢀ11ꢀꢀꢀ=ꢀꢀꢀOFFꢀmodeꢀrequestꢀꢀꢀ  
ꢀꢀShutꢁOffꢀꢀmodeꢀrequestꢀꢀꢀ  
ꢀꢀStartꢁUpꢀꢀmodeꢀrequestꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀSupervisoryꢀꢀModeꢀControlꢀꢀꢀ  
ꢀꢀManualꢀꢀOPꢀModeꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 42 of 51  
General dynamic Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
ꢀꢀꢀ  
38ꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀLSCꢀꢀ  
ꢀꢀMNTꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀRASꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀIASꢀꢀ  
ꢀꢀAFMꢀꢀ  
ꢀꢀSupervisoryꢀꢀSystemꢀꢀActiveꢀꢀRefreshꢀ  
ꢀꢀControlꢀ&ꢀstatusꢀꢀꢀꢀꢀꢀ  
ꢀꢀMaintenanceꢀꢀStartedꢀꢀꢀꢀ  
ꢀꢀMaintenanceꢀꢀStoppedꢀꢀꢀꢀ  
ꢀꢀReverseꢀꢀActionꢀꢀꢀꢀꢀ  
ꢀꢀLoopꢀ#1ꢀActiveꢀꢀꢀ  
ꢀꢀIntrusionꢀꢀAlarmꢀꢀꢀ  
ꢀꢀAntiꢀfreezingꢀꢀModeꢀActiveꢀ  
ꢀꢀThreeꢀspeedꢀFanꢀOverrideꢀRealꢀStatusꢀ  
ꢀꢀLoopꢀ#3ꢀActiveꢀ  
ꢀꢀConstantꢀK1ꢀModuleꢀ#1ꢀꢀꢀ  
ꢀꢀInputꢀConnectionꢀI1@ꢀꢀꢀꢀ  
ꢀꢀInputꢀConnectionꢀI2@ꢀꢀꢀꢀ  
ꢀꢀInputꢀConnectionꢀI3@ꢀꢀꢀꢀ  
ꢀꢀOptionsꢀꢀꢀꢀ  
ꢀꢀConstantꢀK2ꢀꢀꢀ  
ꢀꢀConstantꢀK3ꢀꢀꢀ  
ꢀꢀConstantꢀK4ꢀꢀꢀ  
ꢀꢀConstantꢀK5ꢀꢀꢀ  
ꢀꢀConstantꢀK6ꢀꢀꢀ  
ꢀꢀConstantꢀK7ꢀꢀꢀ  
ꢀꢀConstantꢀK1ꢀModuleꢀ#2ꢀꢀꢀ  
ꢀꢀInputꢀConnectionꢀI1@ꢀꢀꢀꢀ  
ꢀꢀInputꢀConnectionꢀI2@ꢀ  
ꢀꢀInputꢀConnectionꢀI3@ꢀ  
ꢀꢀOptionsꢀ  
ꢀꢀConstantꢀK2ꢀ  
ꢀꢀConstantꢀK3ꢀ  
ꢀꢀConstantꢀK4ꢀ  
ꢀꢀConstantꢀK5ꢀ  
ꢀꢀFOSꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
39ꢀꢀ  
40ꢀꢀ  
41ꢀꢀ  
42ꢀꢀ  
43ꢀꢀ  
44ꢀꢀ  
45ꢀꢀ  
46ꢀꢀ  
47ꢀꢀ  
48ꢀꢀ  
49ꢀꢀ  
50ꢀꢀ  
51ꢀꢀ  
52ꢀꢀ  
53ꢀꢀ  
54ꢀꢀ  
55ꢀꢀ  
56ꢀꢀ  
57ꢀꢀ  
58ꢀꢀ  
59ꢀꢀ  
60ꢀꢀ  
61ꢀꢀ  
62ꢀꢀ  
63ꢀꢀ  
64ꢀꢀ  
65ꢀꢀ  
66ꢀꢀ  
67ꢀꢀ  
68ꢀꢀ  
69ꢀꢀ  
70ꢀꢀ  
71ꢀꢀ  
72ꢀꢀ  
73ꢀꢀ  
74ꢀꢀ  
75ꢀꢀ  
76ꢀꢀ  
77ꢀꢀ  
78ꢀꢀ  
79ꢀꢀ  
80ꢀꢀ  
81ꢀꢀ  
82ꢀꢀ  
83ꢀꢀ  
84ꢀꢀ  
85ꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀPM1K1ꢀꢀ  
ꢀꢀPM1I@1ꢀꢀꢀ  
ꢀꢀPM1I@2ꢀꢀꢀ  
ꢀꢀPM1I@3ꢀꢀꢀ  
ꢀꢀPM1TYPꢀꢀꢀ  
ꢀꢀPM1K2ꢀꢀ  
ꢀꢀPM1K3ꢀꢀ  
ꢀꢀPM1K4ꢀꢀ  
ꢀꢀPM1K5ꢀꢀ  
ꢀꢀPM1K6ꢀꢀ  
ꢀꢀPM1K7ꢀꢀ  
ꢀꢀPM2K1ꢀꢀ  
ꢀꢀPM2I@1ꢀꢀꢀ  
ꢀꢀPM2I@2ꢀꢀꢀ  
ꢀꢀPM2I@3ꢀꢀꢀ  
ꢀꢀPM2TYPꢀꢀꢀ  
ꢀꢀPM2K2ꢀꢀ  
ꢀꢀPM2K3ꢀꢀ  
ꢀꢀPM2K4ꢀꢀ  
ꢀꢀPM2K5ꢀꢀ  
ꢀꢀPM2K6ꢀꢀ  
ꢀꢀPM2K7ꢀꢀ  
ꢀꢀPM3K1ꢀꢀ  
ꢀꢀPM3I@1ꢀꢀꢀ  
ꢀꢀPM3I@2ꢀꢀꢀ  
ꢀꢀPM3I@3ꢀꢀꢀ  
ꢀꢀPM3TYPꢀꢀꢀ  
ꢀꢀPM3K2ꢀꢀ  
ꢀꢀPM3K3ꢀꢀ  
ꢀꢀPM3K4ꢀꢀ  
ꢀꢀPM3K5ꢀꢀ  
ꢀꢀPM3K6ꢀꢀ  
ꢀꢀPM3K7ꢀꢀ  
ꢀꢀPM4K1ꢀꢀ  
ꢀꢀPM4I@1ꢀꢀꢀ  
ꢀꢀPM4I@2ꢀꢀꢀ  
ꢀꢀPM4I@3ꢀꢀꢀ  
ꢀꢀPM4TYPꢀꢀꢀ  
ꢀꢀPM4K2ꢀꢀ  
ꢀꢀPM4K3ꢀꢀ  
ꢀꢀPM4K4ꢀꢀ  
ꢀꢀPM4K5ꢀꢀ  
ꢀꢀPM4K6ꢀꢀ  
ꢀꢀPM4K7ꢀꢀ  
ꢀꢀPM5K1ꢀꢀ  
ꢀꢀPM5I@1ꢀꢀꢀ  
ꢀꢀPM5I@2ꢀꢀꢀ  
ꢀꢀConstantꢀK6ꢀ  
ꢀꢀConstantꢀK7ꢀ  
ꢀꢀConstantꢀK1ꢀModuleꢀ#3ꢀ  
ꢀꢀInputꢀConnectionꢀI1@ꢀ  
ꢀꢀInputꢀConnectionꢀI2@ꢀ  
ꢀꢀInputꢀConnectionꢀI3@ꢀ  
ꢀꢀOptionsꢀ  
ꢀꢀConstantꢀK2ꢀ  
ꢀꢀConstantꢀK3ꢀ  
ꢀꢀConstantꢀK4ꢀ  
ꢀꢀConstantꢀK5ꢀ  
ꢀꢀConstantꢀK6ꢀ  
ꢀꢀConstantꢀK7ꢀ  
ꢀꢀConstantꢀK1ꢀModuleꢀ#4ꢀ  
ꢀꢀInputꢀConnectionꢀI1@ꢀ  
ꢀꢀInputꢀConnectionꢀI2@ꢀ  
ꢀꢀInputꢀConnectionꢀI3@ꢀ  
ꢀꢀOptionsꢀ  
ꢀꢀConstantꢀK2ꢀ  
ꢀꢀConstantꢀK3ꢀ  
ꢀꢀConstantꢀK4ꢀ  
ꢀꢀConstantꢀK5ꢀ  
ꢀꢀConstantꢀK6ꢀ  
ꢀꢀConstantꢀK7ꢀ  
ꢀꢀConstantꢀK1ꢀModuleꢀ#5ꢀ  
ꢀꢀInputꢀConnectionꢀI1@ꢀ  
ꢀꢀInputꢀConnectionꢀI2@ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 43 of 51  
General dynamic Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
86ꢀꢀ  
87ꢀꢀ  
88ꢀꢀ  
89ꢀꢀ  
90ꢀꢀ  
91ꢀꢀ  
92ꢀꢀ  
93ꢀꢀ  
94ꢀꢀ  
95ꢀꢀ  
96ꢀꢀ  
97ꢀꢀ  
98ꢀꢀ  
99ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀPM5I@3ꢀꢀꢀ  
ꢀꢀPM5TYPꢀꢀꢀ  
ꢀꢀPM5K2ꢀꢀ  
ꢀꢀPM5K3ꢀꢀ  
ꢀꢀPM5K4ꢀꢀ  
ꢀꢀPM5K5ꢀꢀ  
ꢀꢀPM5K6ꢀꢀ  
ꢀꢀPM5K7ꢀꢀ  
ꢀꢀPM6K1ꢀꢀ  
ꢀꢀPM6I@1ꢀꢀꢀ  
ꢀꢀPM6I@2ꢀꢀꢀ  
ꢀꢀPM6I@3ꢀꢀꢀ  
ꢀꢀPM6TYPꢀꢀꢀ  
ꢀꢀPM6K2ꢀꢀ  
ꢀꢀPM6K3ꢀꢀ  
ꢀꢀPM6K4ꢀꢀ  
ꢀꢀPM6K5ꢀꢀ  
ꢀꢀPM6K6ꢀꢀ  
ꢀꢀPM6K7ꢀꢀ  
ꢀꢀInputꢀConnectionꢀI3@ꢀ  
ꢀꢀOptionsꢀ  
ꢀꢀConstantꢀK2ꢀ  
ꢀꢀConstantꢀK3ꢀ  
ꢀꢀConstantꢀK4ꢀ  
ꢀꢀConstantꢀK5ꢀ  
ꢀꢀConstantꢀK6ꢀ  
ꢀꢀConstantꢀK7ꢀ  
ꢀꢀConstantꢀK1ꢀModuleꢀ#6ꢀ  
ꢀꢀInputꢀConnectionꢀI1@ꢀ  
ꢀꢀInputꢀConnectionꢀI2@ꢀ  
ꢀꢀInputꢀConnectionꢀI3@ꢀ  
ꢀꢀOptionsꢀ  
ꢀꢀConstantꢀK2ꢀ  
ꢀꢀConstantꢀK3ꢀ  
ꢀꢀConstantꢀK4ꢀ  
ꢀꢀConstantꢀK5ꢀ  
100ꢀꢀꢀ  
101ꢀꢀꢀ  
102ꢀꢀꢀ  
103ꢀꢀꢀ  
104ꢀꢀꢀ  
ꢀꢀConstantꢀK6ꢀ  
ꢀꢀConstantꢀK7ꢀ  
Input Output Config Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
105ꢀꢀꢀ  
106ꢀꢀꢀ  
107ꢀꢀꢀ  
108ꢀꢀꢀ  
109ꢀꢀꢀ  
110ꢀꢀꢀ  
111ꢀꢀꢀ  
112ꢀꢀꢀ  
113ꢀꢀꢀ  
114ꢀꢀꢀ  
115ꢀꢀꢀ  
116ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀSpareꢀꢀ  
ꢀꢀSpareꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀVERꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀFirmwareꢀVersionꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀHIA1ꢀꢀ  
ꢀꢀLOA1ꢀꢀ  
ꢀꢀHIA2ꢀꢀ  
ꢀꢀLOA2ꢀꢀ  
ꢀꢀHIA3ꢀꢀ  
ꢀꢀLOA3ꢀꢀ  
ꢀꢀHIA4ꢀꢀ  
ꢀꢀLOA4ꢀꢀ  
ꢀꢀOCN1ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀHighꢀAlarmꢀAI1ꢀꢀꢀꢀꢀ  
ꢀꢀLowꢀAlarmꢀAI1ꢀꢀꢀꢀ  
ꢀꢀHighꢀAlarmꢀAI2ꢀꢀꢀꢀꢀ  
ꢀꢀLowꢀAlarmꢀAI2ꢀꢀꢀꢀ  
ꢀꢀHighꢀAlarmꢀAI3ꢀꢀꢀꢀꢀ  
ꢀꢀLowꢀAlarmꢀAI3ꢀꢀꢀꢀ  
ꢀꢀHighꢀAlarmꢀAI4ꢀꢀꢀꢀꢀ  
ꢀꢀLowꢀAlarmꢀAI4ꢀꢀꢀꢀ  
ꢀꢀOutputꢀ#1ꢀConfigurationꢀꢀꢀꢀꢀ  
ꢀꢀ00001ꢀSrcꢀofꢀModuleꢀ(AnalogꢀItemsꢀ1..31)ꢀ  
ꢀꢀ?.ꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11111ꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀ001ꢀ=ꢀꢀOutputꢀꢀforꢀSolenoidsꢀ  
ꢀꢀ010ꢀ=ꢀ0ꢀꢀtoꢀ10ꢀVꢀAnalogꢀOutputꢀ  
ꢀꢀ011ꢀ=ꢀꢀON/OFFꢀꢀOutputꢀ  
ꢀꢀ100ꢀ=ꢀꢀDATꢀꢀOutputꢀTypeꢀ  
ꢀꢀ101ꢀ=ꢀꢀPATꢀꢀOutputꢀTypeꢀ  
ꢀꢀ110ꢀ=ꢀꢀMultistageꢀON/OFFꢀTypeꢀ  
ꢀꢀPAT/DATꢀTimingꢀforꢀOutputꢀModuleꢀ#1ꢀꢀꢀꢀꢀ  
ꢀꢀOutputꢀ#2ꢀConfigurationꢀꢀꢀꢀꢀ  
ꢀꢀ00001ꢀSrcꢀofꢀModuleꢀ(AnalogꢀItemsꢀ1..31)ꢀ  
ꢀꢀ?.ꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
117ꢀꢀꢀ  
118ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀOCO1ꢀꢀ  
ꢀꢀOCN2ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11111ꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀ001ꢀ=ꢀꢀOutputꢀꢀforꢀSolenoidsꢀ  
ꢀꢀ010ꢀ=ꢀ0ꢀꢀtoꢀ10ꢀVꢀAnalogꢀOutputꢀ  
ꢀꢀ011ꢀ=ꢀꢀON/OFFꢀꢀOutputꢀ  
ꢀꢀPATꢀDeadꢀBand/MultistateꢀHysteresisꢀ#1ꢀꢀꢀꢀꢀ  
ꢀꢀOutputꢀ#3ꢀConfigurationꢀꢀꢀꢀꢀ  
ꢀꢀ00001ꢀSrcꢀofꢀModuleꢀ(AnalogꢀItemsꢀ1..31)ꢀ  
ꢀꢀ?.ꢀꢀꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
119ꢀꢀꢀ  
120ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀOCO2ꢀꢀ  
ꢀꢀOCN3ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 44 of 51  
Input Output Config Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11111ꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀ011ꢀ=ꢀꢀON/OFFꢀꢀOutputꢀ  
ꢀꢀ100ꢀ=ꢀꢀDATꢀꢀOutputꢀTypeꢀ  
ꢀꢀ101ꢀ=ꢀꢀPATꢀꢀOutputꢀTypeꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ110ꢀ=ꢀꢀMultistageꢀON/OFFꢀTypeꢀ  
ꢀꢀPAT/DATꢀTimingꢀforꢀOutputꢀModuleꢀ#3ꢀꢀꢀꢀꢀ  
ꢀꢀOutputꢀ#4ꢀConfigurationꢀꢀꢀꢀꢀ  
ꢀꢀ00001ꢀSrcꢀofꢀModuleꢀ(AnalogꢀItemsꢀ1..31)ꢀ  
ꢀꢀ?.ꢀꢀꢀꢀꢀ  
121ꢀꢀꢀ  
122ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀOCO3ꢀꢀ  
ꢀꢀOCN4ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
123ꢀꢀꢀ  
124ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀOCO4ꢀꢀ  
ꢀꢀOCN5ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11111ꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀ011ꢀ=ꢀꢀON/OFFꢀꢀOutputꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀPATꢀDeadꢀBand/MultistateꢀHysteresisꢀ#3ꢀꢀꢀꢀꢀ  
ꢀꢀOutputꢀ#5ꢀConfigurationꢀꢀꢀꢀꢀ  
ꢀꢀ00001ꢀSrcꢀofꢀModuleꢀ(AnalogꢀItemsꢀ1..31)ꢀ  
ꢀꢀ?.ꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11111ꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀ011ꢀ=ꢀꢀON/OFFꢀꢀOutputꢀ  
ꢀꢀ100ꢀ=ꢀꢀDATꢀꢀOutputꢀTypeꢀ  
ꢀꢀ101ꢀ=ꢀꢀPATꢀꢀOutputꢀTypeꢀ  
ꢀꢀ110ꢀ=ꢀꢀMultistageꢀON/OFFꢀTypeꢀ  
ꢀꢀ111ꢀ=ꢀꢀThreeꢀWindingsꢀControlꢀ  
ꢀꢀPAT/DATꢀTimgꢀOutptꢀModꢀ#5ꢀFSBꢁpntꢀ#1ꢀꢀꢀꢀ  
ꢀꢀOutputꢀ#6ꢀConfigurationꢀꢀꢀꢀꢀ  
ꢀꢀ00001ꢀSrcꢀofꢀModuleꢀ(AnalogꢀItemsꢀ1..31)ꢀ  
ꢀꢀ?.ꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
125ꢀꢀꢀ  
126ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀOCO5ꢀꢀ  
ꢀꢀOCN6ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11111ꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
127ꢀꢀꢀ  
128ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀOCO6ꢀꢀ  
ꢀꢀOCN7ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀPAT/DATꢀTimgꢀOutptꢀModꢀ#5ꢀFSBꢁpntꢀ#2ꢀꢀꢀꢀ  
ꢀꢀOutputꢀ#7ꢀConfigurationꢀꢀꢀꢀꢀ  
ꢀꢀ00001ꢀSrcꢀofꢀModuleꢀ(AnalogꢀItemsꢀ1..31)ꢀ  
ꢀꢀ?.ꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11111ꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀspareꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀW(2)ꢀꢀ  
ꢀꢀW(3)ꢀꢀ  
ꢀꢀW(4)ꢀꢀ  
ꢀꢀW(5)ꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(8)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀW(10)ꢀꢀ  
ꢀꢀW(11)ꢀꢀ  
ꢀꢀW(12)ꢀꢀ  
ꢀꢀW(13)ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀOCO7ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀALGꢀꢀ  
ꢀꢀXSTꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDIALꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
129ꢀꢀꢀ  
130ꢀꢀꢀ  
131ꢀꢀꢀ  
132ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀFanꢀSpeedꢀBreakꢁpointꢀ#3ꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀConfigurationꢀIndexꢀ1ꢀꢀꢀꢀ  
ꢀꢀDiagnosticꢀStatusꢀꢀꢀꢀ  
ꢀꢀGainꢀxꢀꢀ2ꢀJumperꢀ  
ꢀꢀIntegralꢀꢀActionꢀꢀZeroingꢀJumperꢀ  
ꢀꢀZoneꢀ1ꢀꢀJumperꢀ  
ꢀꢀZoneꢀ2ꢀꢀJumperꢀ  
ꢀꢀDialꢀRequestꢀStatusꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀIntelligentꢀCommandꢀModuleꢀComꢀFailureꢀ  
ꢀꢀnotꢀꢀvalidꢀꢀ  
ꢀꢀnotꢀꢀvalidꢀꢀ  
ꢀꢀnotꢀꢀvalidꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀClearꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀXTAI1ꢀꢀ  
ꢀꢀXTAI2ꢀꢀ  
ꢀꢀXTAI3ꢀꢀ  
ꢀꢀXTAI4ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀnotꢀꢀvalidꢀꢀ  
ꢀꢀEEPROMꢀꢀnotꢀꢀprotectedꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 45 of 51  
Input Output Config Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
133ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(14)ꢀꢀ  
ꢀꢀW(15)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTCS2ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀResetꢀCycleꢀindicationꢀꢀꢀꢀ  
ꢀꢀ00ꢀꢀ=ꢀꢀPowerꢀUpꢀResetꢀꢀꢀ  
ꢀꢀ01ꢀꢀ=ꢀꢀExternalꢀꢀResetꢀꢀ  
ꢀꢀ10ꢀꢀ=ꢀꢀOscillatorꢀFailureꢀꢀꢀ  
ꢀꢀ11ꢀꢀ=ꢀꢀWatchdogꢀResetꢀꢀꢀ  
ꢀꢀTC9100ꢀControllerꢀOptionsꢀꢀꢀꢀꢀꢀ  
ꢀꢀ00ꢀꢀSelectꢀꢀAnalogꢀꢀInputꢀ1ꢀADCꢀꢀ  
ꢀꢀtoꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀW(16)ꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(2)ꢀꢀ  
ꢀꢀW(3)ꢀꢀ  
ꢀꢀW(4)ꢀꢀ  
ꢀꢀW(5)ꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(7)ꢀꢀ  
ꢀꢀW(8)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11ꢀꢀSelectꢀꢀAnalogꢀꢀInputꢀ4ꢀADCꢀꢀ  
ꢀꢀTM9100ꢀdoesꢀnotꢀoverrdꢀtheꢀprocꢀVariableꢀꢀ  
ꢀꢀHalfꢀꢀAlternateꢀꢀModeꢀTimingꢀꢀ  
ꢀꢀ0ꢀꢀ=ꢀꢀCelsiusꢀꢀꢀꢀ1ꢀ=ꢀFahrenheitꢀ  
ꢀꢀ0ꢀꢀ=ꢀ50ꢀꢀHzꢀ1ꢀ=ꢀ60ꢀHzꢀPowerꢀLineꢀ  
ꢀꢀEnableꢀFacilitatorꢀꢀModeꢀꢀꢀꢀ  
ꢀꢀTRIAC7ꢀisꢀONꢀifꢀmodeꢀisꢀComfortꢀꢀꢀ  
ꢀꢀDigitalꢀꢀInputꢀ#1ꢀModeꢀꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ001ꢀ=ꢀꢀWindowꢀꢀOpenꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀW(11)ꢀꢀ  
ꢀꢀW(12)ꢀꢀ  
ꢀꢀW(13)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ010ꢀ=ꢀꢀOccupancyꢀꢀSensorꢀ  
ꢀꢀ011ꢀ=ꢀꢀAirꢀꢀQualityꢀSensorꢀ  
ꢀꢀ100ꢀ=ꢀꢀReverseꢀꢀActionꢀ  
ꢀꢀ101ꢀ=ꢀꢀIntrusionꢀꢀAlarmꢀ  
ꢀꢀNegateꢀDigitalꢀꢀInputꢀ#1ꢀ  
ꢀꢀDigitalꢀꢀInputꢀ#2ꢀModeꢀ  
ꢀꢀ000ꢀ=ꢀꢀNotꢀꢀusedꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ001ꢀ=ꢀꢀWindowꢀꢀOpenꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
134ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
135ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
136ꢀꢀꢀ  
137ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTCS3ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTCS1ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀHDW1ꢀꢀ  
ꢀꢀHRI1ꢀꢀ  
ꢀꢀ010ꢀ=ꢀꢀOccupancyꢀꢀSensorꢀ  
ꢀꢀ011ꢀ=ꢀꢀAirꢀꢀQualityꢀSensorꢀ  
ꢀꢀ100ꢀ=ꢀꢀReverseꢀꢀActionꢀ  
ꢀꢀ101ꢀ=ꢀꢀIntrusionꢀꢀAlarmꢀ  
ꢀꢀNegateꢀꢀDigitalꢀꢀInputꢀ#2ꢀ  
ꢀꢀEnableꢀJumperꢀOptionsꢀꢀꢀꢀ  
ꢀꢀEnableꢀꢀIntegralꢀꢀZeroingꢀꢀLoopꢀ#1ꢀ  
ꢀꢀEnableꢀꢀIntegralꢀꢀZeroingꢀꢀLoopꢀ#2ꢀ  
ꢀꢀEnableꢀꢀIntegralꢀꢀZeroingꢀꢀLoopꢀ#3ꢀ  
ꢀꢀEnableꢀꢀIntegralꢀꢀZeroingꢀꢀLoopꢀ#4ꢀ  
ꢀꢀEnableꢀꢀIntegralꢀꢀZeroingꢀꢀLoopꢀ#5ꢀ  
ꢀꢀEnableꢀꢀIntegralꢀꢀZeroingꢀꢀLoopꢀ#6ꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀW(15)ꢀꢀ  
ꢀꢀW(16)ꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀW(2)ꢀꢀ  
ꢀꢀW(3)ꢀꢀ  
ꢀꢀW(4)ꢀꢀ  
ꢀꢀW(5)ꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(7)ꢀꢀ  
ꢀꢀW(8)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀW(10)ꢀꢀ  
ꢀꢀW(11)ꢀꢀ  
ꢀꢀW(12)ꢀꢀ  
ꢀꢀW(13)ꢀꢀ  
ꢀꢀW(14)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀEnableꢀꢀGainꢀDoublingꢀꢀLoopꢀ#1ꢀ  
ꢀꢀEnableꢀꢀGainꢀDoublingꢀꢀLoopꢀ#2ꢀ  
ꢀꢀEnableꢀꢀGainꢀDoublingꢀꢀLoopꢀ#3ꢀ  
ꢀꢀEnableꢀꢀGainꢀDoublingꢀꢀLoopꢀ#4ꢀ  
ꢀꢀEnableꢀꢀGainꢀDoublingꢀꢀLoopꢀ#5ꢀ  
ꢀꢀEnableꢀꢀGainꢀDoublingꢀꢀLoopꢀ#6ꢀ  
ꢀꢀControllerꢀOptionsꢀꢀꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀDefaultꢀꢀActionꢀꢀ1=Reverseꢀꢀ  
ꢀꢀHardwareꢀConfigurationꢀꢀꢀꢀꢀ  
ꢀꢀHighꢀRangeꢀAI1ꢀꢀꢀꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 46 of 51  
Input Output Config Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
138ꢀꢀꢀ  
139ꢀꢀꢀ  
140ꢀꢀꢀ  
141ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀLRI1ꢀꢀ  
ꢀꢀFTC1ꢀꢀ  
ꢀꢀOFS1ꢀꢀ  
ꢀꢀIOP1ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀLowꢀRangeꢀAI1ꢀꢀꢀꢀ  
ꢀꢀFilterꢀConstantꢀAI1ꢀꢀꢀꢀꢀ  
ꢀꢀOffsetꢀCompensationꢀAI1ꢀꢀꢀꢀꢀ  
ꢀꢀAnalogꢀInputꢀOptionsꢀꢀꢀꢀꢀ  
ꢀꢀControllerꢀreferenceꢀꢀꢀꢀꢀ  
ꢀꢀ1ꢀꢀtoꢀꢀ6ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀInputꢀType:ꢀ0=voltꢀꢀ1=resistanceꢀ  
ꢀꢀInputꢀModeꢀꢀꢀꢀꢀ  
ꢀꢀ000ꢀꢁꢀꢀLinearꢀꢀRangeꢀꢀ  
ꢀꢀ001ꢁThermistorꢀLinearizationꢀ2252.atꢀ25Cꢀꢀ  
ꢀꢀ010ꢀꢁꢀꢀSquareꢀꢀRootꢀꢀ  
ꢀꢀ011ꢀꢁꢀ0.2ꢀsuppressionꢀꢀ  
ꢀꢀ100ꢁThermistorꢀLinearizationꢀ10ꢀk.ꢀatꢀ25Cꢀꢀ  
ꢀꢀ101ꢀꢁꢀꢀSquareꢀꢀRootꢀ&ꢀ20ꢀ%ꢀsuppressionꢀꢀꢀ  
ꢀꢀNotꢀusedꢀꢀꢀꢀꢀ  
ꢀꢀHighꢀRangeꢀAI2ꢀꢀꢀꢀꢀꢀ  
ꢀꢀLowꢀRangeꢀAI2ꢀꢀꢀꢀ  
ꢀꢀFilterꢀConstantꢀAI2ꢀꢀꢀꢀꢀ  
ꢀꢀOffsetꢀCompensationꢀAI2ꢀꢀꢀꢀꢀ  
ꢀꢀAnalogꢀInputꢀOptionsꢀ(seeꢀIOP1)ꢀꢀꢀꢀꢀ  
ꢀꢀHighꢀRangeꢀAI3ꢀꢀꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
142ꢀꢀꢀ  
143ꢀꢀꢀ  
144ꢀꢀꢀ  
145ꢀꢀꢀ  
146ꢀꢀꢀ  
147ꢀꢀꢀ  
148ꢀꢀꢀ  
149ꢀꢀꢀ  
150ꢀꢀꢀ  
151ꢀꢀꢀ  
152ꢀꢀꢀ  
153ꢀꢀꢀ  
154ꢀꢀꢀ  
155ꢀꢀꢀ  
156ꢀꢀꢀ  
157ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀHRI2ꢀꢀ  
ꢀꢀLRI2ꢀꢀ  
ꢀꢀFTC2ꢀꢀ  
ꢀꢀOFS2ꢀꢀ  
ꢀꢀIOP2ꢀꢀ  
ꢀꢀHRI3ꢀꢀ  
ꢀꢀLRI3ꢀꢀ  
ꢀꢀFTC3ꢀꢀ  
ꢀꢀOFS3ꢀꢀ  
ꢀꢀIOP3ꢀꢀ  
ꢀꢀHRI4ꢀꢀ  
ꢀꢀLRI4ꢀꢀ  
ꢀꢀFTC4ꢀꢀ  
ꢀꢀOFS4ꢀꢀ  
ꢀꢀIOP4ꢀꢀ  
ꢀꢀOSꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀLowꢀRangeꢀAI3ꢀꢀꢀꢀ  
ꢀꢀFilterꢀConstantꢀAI3ꢀꢀꢀꢀꢀ  
ꢀꢀOffsetꢀCompensationꢀAI3ꢀꢀꢀꢀꢀ  
ꢀꢀAnalogꢀInputꢀOptionsꢀ(seeꢀIOP1)ꢀꢀꢀꢀꢀ  
ꢀꢀHighꢀRangeꢀAI4ꢀꢀꢀꢀꢀ  
ꢀꢀLowꢀRangeꢀAI4ꢀꢀꢀꢀ  
ꢀꢀFilterꢀConstantꢀAI4ꢀꢀꢀꢀꢀ  
ꢀꢀOffsetꢀCompensationꢀAI4ꢀꢀꢀꢀꢀ  
ꢀꢀAnalogꢀInputꢀOptionsꢀ(seeꢀIOP1)ꢀꢀꢀꢀꢀ  
ꢀꢀTC9100ꢀRequestedꢀOperatingꢀStatusꢀꢀꢀꢀꢀ  
ꢀꢀ00ꢀꢀ=ꢀꢀNightꢀmodeꢀ  
ꢀꢀ01ꢀꢀ=ꢀꢀStandꢁbyꢀꢀmodeꢀ  
ꢀꢀ10ꢀꢀ=ꢀꢀComfortꢀꢀmodeꢀ  
ꢀꢀ11ꢀꢀ=ꢀꢀOFFꢀꢀmodeꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀB(6)ꢀꢀ  
ꢀꢀB(7)ꢀꢀ  
ꢀꢀB(8)ꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀOperatingꢀꢀModeꢀToggle:ꢀBaseꢁꢀAlternateꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀForceꢀOperatingꢀꢀModeꢀꢀ  
ꢀꢀCommandꢀꢀModuleꢀꢀActiveꢀꢀꢀ  
ꢀꢀTM9100ꢀRealꢀTimeꢀClkꢀSynchronizationꢀꢀꢀꢀꢀ  
ꢀꢀMinutesꢀꢀ0..59ꢀꢀꢀ  
ꢀꢀꢀ  
158ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSTIMEꢀꢀ  
ꢀꢀRTCꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(7)ꢀꢀ  
ꢀꢀW(8)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀRTCꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀSpareꢀꢀꢀꢀ  
ꢀꢀSpareꢀꢀꢀꢀ  
ꢀꢀHoursꢀ0..23ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(13)ꢀꢀ  
ꢀꢀW(14)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀRTCꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀ  
ꢀꢀDayꢀꢀofꢀWeekꢀ1..7ꢀ  
ꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(16)ꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀ  
159ꢀꢀꢀ  
160ꢀꢀꢀ  
161ꢀꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀOT@ꢀꢀ  
ꢀꢀSPWꢀꢀ  
ꢀꢀSPSꢀꢀ  
ꢀꢀOutdoorꢀTemperatureꢀConnectionꢀꢀꢀ  
ꢀꢀWinterꢀsetꢀpointꢀꢀꢀꢀ  
ꢀꢀSummerꢀsetꢀpointꢀꢀꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 47 of 51  
Input Output Config Parametersꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
162ꢀꢀꢀ  
163ꢀꢀꢀ  
164ꢀꢀꢀ  
165ꢀꢀꢀ  
166ꢀꢀꢀ  
167ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWAꢀꢀꢀ  
ꢀꢀSAꢀꢀꢀ  
ꢀꢀFT@ꢀꢀ  
ꢀꢀFSPꢀꢀ  
ꢀꢀFDIFꢀꢀ  
ꢀꢀLOOꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWinterꢀAuthorityꢀSlopeꢀꢀꢀ  
ꢀꢀSummerꢀAuthorityꢀSlopeꢀꢀꢀ  
ꢀꢀFreezeꢀTemperatureꢀconnectionꢀꢀꢀ  
ꢀꢀFreezeꢀsetꢀpointꢀꢀꢀꢀ  
ꢀꢀFreezeꢀDifferentialꢀꢀꢀ  
ꢀꢀInput/OutputꢀOverrideꢀControlꢀꢀꢀꢀ  
ꢀꢀThreeꢀSpeedꢀFanꢀActualꢀSpeedꢀꢀꢀ  
ꢀꢀ00ꢀꢀ=ꢀꢀOutputꢀꢀOFFꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ01ꢀꢀ=ꢀꢀSpeedꢀ#1ꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ10ꢀꢀ=ꢀꢀSpeedꢀ#2ꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(2)ꢀꢀ  
ꢀꢀW(3)ꢀꢀ  
ꢀꢀW(4)ꢀꢀ  
ꢀꢀW(5)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀFOSꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11ꢀꢀ=ꢀꢀSpeedꢀ#3ꢀꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀꢀꢀ  
ꢀꢀThreeꢀspdꢀFanꢀOverrdꢀReqstꢀbyꢀHardwareꢀꢀꢀꢀ  
ꢀꢀFanꢀꢀSpeedꢀReqstꢀbyꢀCommandꢀModuleꢀꢀ  
ꢀꢀ00ꢀꢀ=ꢀꢀOutputꢀꢀOFFꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ01ꢀꢀ=ꢀꢀSpeedꢀ#1ꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ10ꢀꢀ=ꢀꢀSpeedꢀ#2ꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
168ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(7)ꢀꢀ  
ꢀꢀW(8)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀW(10)ꢀꢀ  
ꢀꢀW(11)ꢀꢀ  
ꢀꢀW(12)ꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀW(2)ꢀꢀ  
ꢀꢀW(3)ꢀꢀ  
ꢀꢀW(4)ꢀꢀ  
ꢀꢀW(5)ꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(7)ꢀꢀ  
ꢀꢀW(8)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀW(10)ꢀꢀ  
ꢀꢀW(11)ꢀꢀ  
ꢀꢀW(12)ꢀꢀ  
ꢀꢀW(13)ꢀꢀ  
ꢀꢀW(14)ꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11ꢀꢀ=ꢀꢀSpeedꢀ#3ꢀ  
ꢀꢀTM9100ꢀꢀRealꢀTimeꢀClkꢀRefreshꢀRequestꢀ  
ꢀꢀThreeꢀspeedꢀFanꢀOverrdꢀReqstꢀCmdꢀModꢀꢀꢀ  
ꢀꢀAnalogꢀꢀInputꢀ#1ꢀOverrideꢀꢀ  
ꢀꢀAnalogꢀꢀInputꢀ#2ꢀOverrideꢀ  
ꢀꢀAnalogꢀꢀInputꢀ#3ꢀOverrideꢀ  
ꢀꢀAnalogꢀꢀInputꢀ#4ꢀOverrideꢀ  
ꢀꢀControlꢀLoopsꢀActivityꢀModeꢀꢀꢀ  
ꢀꢀLoopꢀ#1ꢀHeatingꢀ  
ꢀꢀLoopꢀ#2ꢀHeatingꢀ  
ꢀꢀLoopꢀ#3ꢀHeatingꢀ  
ꢀꢀLoopꢀ#4ꢀHeatingꢀ  
ꢀꢀLoopꢀ#5ꢀHeatingꢀ  
ꢀꢀLoopꢀ#6ꢀHeatingꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀNotꢀꢀusedꢀꢀ  
ꢀꢀLoopꢀ#1ꢀActiveꢀ  
ꢀꢀLoopꢀ#2ꢀActiveꢀ  
ꢀꢀLoopꢀ#3ꢀActiveꢀ  
ꢀꢀLoopꢀ#4ꢀActiveꢀ  
ꢀꢀLoopꢀ#5ꢀActiveꢀ  
ꢀꢀFORꢀꢀ  
ꢀꢀAIO1ꢀꢀ  
ꢀꢀAIO2ꢀꢀ  
ꢀꢀAIO3ꢀꢀ  
ꢀꢀAIO4ꢀꢀ  
ꢀꢀCLACTꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀR/Wꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀLoopꢀ#6ꢀActiveꢀ  
169ꢀꢀꢀ  
170ꢀꢀꢀ  
171ꢀꢀꢀ  
ꢀꢀALG2ꢀꢀ  
ꢀꢀWALꢀꢀ  
ꢀꢀSALꢀꢀ  
ꢀꢀConfigurationꢀIndexꢀ2ꢀꢀꢀ  
ꢀꢀWinterꢀAuthorityꢀLimitꢀꢀꢀ  
ꢀꢀSummerꢀAuthorityꢀLimitꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
Items Stored in the TM91xx External Databaseꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
256ꢀꢀꢀ  
257ꢀꢀꢀ  
258ꢀꢀꢀ  
259ꢀꢀꢀ  
260ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀFPꢀꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀReadꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀUNITꢀꢀ  
ꢀꢀTEMPꢀꢀ  
ꢀꢀRSPꢀꢀ  
ꢀꢀLOOꢀꢀ  
ꢀꢀJMPꢀꢀ  
ꢀꢀJMP1ꢀꢀ  
ꢀꢀJMP2ꢀꢀ  
ꢀꢀJMP3ꢀꢀ  
ꢀꢀJMP4ꢀꢀ  
ꢀꢀJMP5ꢀꢀ  
ꢀꢀTIMEꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDeviceꢀModelꢀ:ꢀxxHꢀꢀꢀꢀ  
ꢀꢀRoomꢀTemperatureꢀꢀꢀꢀ  
ꢀꢀRemoteꢀTemperatureꢀSetꢀPointꢀꢀꢀꢀ  
ꢀꢀCopyꢀofꢀTC9100ꢀItemꢀLOOꢀꢀꢀꢀ  
ꢀꢀTM9100ꢀJumperꢀConfigurationꢀ&ꢀstatusꢀꢀꢀꢀ  
ꢀꢀClockꢀSettingꢀꢀDisableꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀByteꢀꢀ  
ꢀꢀB(1)ꢀꢀ  
ꢀꢀB(2)ꢀꢀ  
ꢀꢀB(3)ꢀꢀ  
ꢀꢀB(4)ꢀꢀ  
ꢀꢀB(5)ꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀFanꢀꢀSettingꢀꢀDisableꢀꢀꢀ  
ꢀꢀTimeꢀScheduleꢀꢀSettingꢀDisableꢀꢀꢀ  
ꢀꢀModelꢀwithꢀTimeꢀScheduleꢀꢀ  
ꢀꢀTimeꢀScheduleꢀꢀConfigurationꢀChangedꢀꢀ  
ꢀꢀRealꢀTimeꢀꢀꢀꢀꢀ  
261ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀRTCꢀꢀMinutesꢀꢀ0..59ꢀꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 48 of 51  
Items Stored in the TM91xx External Databaseꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀW(13)ꢀꢀ  
ꢀꢀW(14)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀRTCꢀꢀHoursꢀ0..23ꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀRTCꢀꢀDyꢀofꢀWeekꢀ1..7ꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀW(16)ꢀꢀ  
TM91xx Daily Schedules:ꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
271ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀW(1)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDST1ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTypeꢀofꢀDailyꢀScheduleꢀ#1ꢀꢀꢀꢀꢀ  
ꢀꢀModeꢀeventꢀ1ꢀꢀꢀ  
ꢀꢀ00ꢀꢀ=ꢀꢀSetꢀꢀNightꢀModeꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ01ꢀꢀ=ꢀꢀSetꢀꢀComfortꢀModeꢀ  
ꢀꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ10ꢀꢀ=ꢀꢀSetꢀꢀStandꢁByꢀModeꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(2)ꢀꢀ  
ꢀꢀW(3)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀ11ꢀꢀ=ꢀꢀSetꢀꢀOFFꢀModeꢀ  
ꢀꢀModeꢀeventꢀ2ꢀꢀ(SameꢀFmt.ꢀModeꢀeventꢀ1)ꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(4)ꢀꢀ  
ꢀꢀW(5)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀModeꢀeventꢀ3ꢀꢀ(SameꢀFmt.ꢀModeꢀeventꢀ1)ꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(6)ꢀꢀ  
ꢀꢀW(7)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀModeꢀeventꢀ4ꢀꢀ(SameꢀFmt.ꢀModeꢀeventꢀ1)ꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(8)ꢀꢀ  
ꢀꢀW(9)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀModeꢀeventꢀ5ꢀꢀ(SameꢀFmt.ꢀModeꢀeventꢀ1)ꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(10)ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(11)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀModeꢀeventꢀ6ꢀꢀ(SameꢀFmt.ꢀModeꢀeventꢀ1)ꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(12)ꢀꢀ  
ꢀꢀW(13)ꢀꢀ  
ꢀꢀ ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀNumberꢀꢀofꢀDaysꢀofꢀactivityꢀ1..7ꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
ꢀꢀꢀ  
ꢀꢀW(15)ꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀꢀꢀꢀ  
272ꢀꢀꢀ  
272ꢀꢀꢀ  
272ꢀꢀꢀ  
273ꢀꢀꢀ  
287ꢀꢀꢀ  
288ꢀꢀꢀ  
289ꢀꢀꢀ  
290ꢀꢀꢀ  
291ꢀꢀꢀ  
292ꢀꢀꢀ  
303ꢀꢀꢀ  
304ꢀꢀꢀ  
305ꢀꢀꢀ  
306ꢀꢀꢀ  
307ꢀꢀꢀ  
308ꢀꢀꢀ  
319ꢀꢀꢀ  
320ꢀꢀꢀ  
321ꢀꢀꢀ  
322ꢀꢀꢀ  
323ꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀE12S1ꢀꢀ  
ꢀꢀE34S1ꢀꢀ  
ꢀꢀE56S1ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀEventꢀ#1ꢀ&ꢀEventꢀ#2ꢀDayꢀ#1ꢀꢀꢀꢀꢀ  
ꢀꢀEventꢀ#3ꢀ&ꢀEventꢀ#4ꢀDayꢀ#1ꢀꢀꢀꢀꢀ  
ꢀꢀEventꢀ#5ꢀ&ꢀEventꢀ#6ꢀDayꢀ#1ꢀꢀꢀꢀꢀ  
ꢀꢀSpareꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSpareꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDST2ꢀꢀ  
ꢀꢀE12S2ꢀꢀ  
ꢀꢀE34S2ꢀꢀ  
ꢀꢀE56S2ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTypeꢀofꢀDailyꢀScheduleꢀ#2ꢀ(Fmt.ꢀ#1)ꢀ  
ꢀꢀEventꢀ#1ꢀ&ꢀEventꢀ#2ꢀDayꢀ#2ꢀ  
ꢀꢀEventꢀ#3ꢀ&ꢀEventꢀ#4ꢀDayꢀ#2ꢀ  
ꢀꢀEventꢀ#5ꢀ&ꢀEventꢀ#6ꢀDayꢀ#2ꢀ  
ꢀꢀSpareꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSpareꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDST3ꢀꢀ  
ꢀꢀE12S3ꢀꢀ  
ꢀꢀE34S3ꢀꢀ  
ꢀꢀE56S3ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTypeꢀofꢀDailyꢀScheduleꢀ#3ꢀ(Fmt.ꢀ#1)ꢀ  
ꢀꢀEventꢀ#1ꢀ&ꢀEventꢀ#2ꢀDayꢀ#3ꢀ  
ꢀꢀEventꢀ#3ꢀ&ꢀEventꢀ#4ꢀDayꢀ#3ꢀ  
ꢀꢀEventꢀ#5ꢀ&ꢀEventꢀ#6ꢀDayꢀ#3ꢀ  
ꢀꢀSpareꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSpareꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀDST4ꢀꢀ  
ꢀꢀE12S4ꢀꢀ  
ꢀꢀE34S4ꢀꢀ  
ꢀꢀE56S4ꢀꢀ  
ꢀꢀTypeꢀofꢀDailyꢀScheduleꢀ#4ꢀ(Fmt.ꢀ#1)ꢀ  
ꢀꢀEventꢀ#1ꢀ&ꢀEventꢀ#2ꢀDayꢀ#4ꢀ  
ꢀꢀEventꢀ#3ꢀ&ꢀEventꢀ#4ꢀDayꢀ#4ꢀ  
ꢀꢀEventꢀ#5ꢀ&ꢀEventꢀ#6ꢀDayꢀ#4ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 49 of 51  
TM91xx Daily Schedules:ꢀ  
Relative Item Signal Condition Read/Write Johnson Tag Description  
324ꢀꢀꢀ  
335ꢀꢀꢀ  
336ꢀꢀꢀ  
337ꢀꢀꢀ  
338ꢀꢀꢀ  
339ꢀꢀꢀ  
340ꢀꢀꢀ  
351ꢀꢀꢀ  
352ꢀꢀꢀ  
353ꢀꢀꢀ  
354ꢀꢀꢀ  
355ꢀꢀꢀ  
356ꢀꢀꢀ  
367ꢀꢀꢀ  
368ꢀꢀꢀ  
369ꢀꢀꢀ  
370ꢀꢀꢀ  
371ꢀꢀꢀ  
372ꢀꢀꢀ  
383ꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSpareꢀ  
ꢀꢀSpareꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDST5ꢀꢀ  
ꢀꢀE12S5ꢀꢀ  
ꢀꢀE34S5ꢀꢀ  
ꢀꢀE56S5ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTypeꢀofꢀDailyꢀScheduleꢀ#5ꢀ(Fmt.ꢀ#1)ꢀ  
ꢀꢀEventꢀ#1ꢀ&ꢀEventꢀ#2ꢀDayꢀ#5ꢀ  
ꢀꢀEventꢀ#3ꢀ&ꢀEventꢀ#4ꢀDayꢀ#5ꢀ  
ꢀꢀEventꢀ#5ꢀ&ꢀEventꢀ#6ꢀDayꢀ#5ꢀ  
ꢀꢀSpareꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSpareꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDST6ꢀꢀ  
ꢀꢀE12S6ꢀꢀ  
ꢀꢀE34S6ꢀꢀ  
ꢀꢀE56S6ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTypeꢀofꢀDailyꢀScheduleꢀ#6ꢀ(Fmt.ꢀ#1)ꢀ  
ꢀꢀEventꢀ#1ꢀ&ꢀEventꢀ#2ꢀDayꢀ#6ꢀ  
ꢀꢀEventꢀ#3ꢀ&ꢀEventꢀ#4ꢀDayꢀ#6ꢀ  
ꢀꢀEventꢀ#5ꢀ&ꢀEventꢀ#6ꢀDayꢀ#6ꢀ  
ꢀꢀSpareꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSpareꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀWordꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀWriteꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀDST7ꢀꢀ  
ꢀꢀE12S7ꢀꢀ  
ꢀꢀE34S7ꢀꢀ  
ꢀꢀE56S7ꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀTypeꢀofꢀDailyꢀScheduleꢀ#7ꢀ(Fmt.ꢀ#1)ꢀ  
ꢀꢀEventꢀ#1ꢀ&ꢀEventꢀ#2ꢀDayꢀ#7ꢀ  
ꢀꢀEventꢀ#3ꢀ&ꢀEventꢀ#4ꢀDayꢀ#7ꢀ  
ꢀꢀEventꢀ#5ꢀ&ꢀEventꢀ#6ꢀDayꢀ#7ꢀ  
ꢀꢀSpareꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀꢀꢀ  
ꢀꢀSpareꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Appendix E. Error Messages  
Page 50 of 51  
Error Message  
Description and Action  
TypicallyꢀN2openꢀClientsꢀareꢀconfiguredꢀtoꢀtimeoutꢀafterꢀ200ms.ꢀꢀIfꢀaꢀ  
FieldServerꢀisꢀconfiguredꢀasꢀaꢀServerꢀtheꢀServer_Hold_Timeoutꢀtimeꢀ  
shouldꢀbeꢀsetꢀtoꢀ0.175sꢀorꢀlessꢀotherwiseꢀtheꢀresponseꢀwillꢀbeꢀsuppressed.ꢀꢀ  
ThisꢀmessageꢀisꢀprintedꢀifꢀtheꢀServer_Hold_Timeoutꢀisꢀsetꢀforꢀ>0.175s.ꢀꢀꢀ  
MN2:#01ꢀWARN.ꢀ  
Server_Hold_Timeoutꢀisꢀ  
%0.3fsꢀ  
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀForꢀN2OpenꢀSlaveꢀ  
typicalꢀvalueꢀisꢀ%0.3fsꢀ  
IfꢀtheꢀClient’sꢀtimeoutꢀisꢀ>200msꢀthisꢀmessageꢀmayꢀbeꢀignored.ꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 
FS-8700-19_Metasys_N2 Driver Manual  
Page 51 of 51  
THISꢀPAGEꢀINTENTIONALLYꢀLEFTꢀBLANKꢀ  
FieldServer Technologiesꢀ1991ꢀTarobꢀCourtꢀMilpitas,ꢀCaliforniaꢀ95035ꢀUSAꢀꢀWeb:www.fieldserver.comꢀ  
Tel:ꢀ(408)ꢀ262ꢁ2299ꢀꢀꢀFax:ꢀ(408)ꢀ262ꢁ2296ꢀꢀꢀToll_Free:ꢀ888ꢁ509ꢁ1970ꢀꢀꢀemail:ꢀsupport@fieldserver.comꢀ  
 

Code Alarm Automobile Alarm CA 680 User Manual
Coleman Camping Equipment 2000000583 User Manual
Conair Electric Shaver HCT21 User Manual
Craftsman Lawn Mower Accessory 48624608 User Manual
Dynacord Music Mixer DRM 4000 User Manual
Elation Professional Work Light Spot 250 User Manual
Euro Pro Carpet Cleaner EP961 User Manual
Fortinet Network Card FortiOS 30 User Manual
Gigabyte Network Card GA K8VT890 9 User Manual
Global Machinery Company Chainsaw PCH37 User Manual