4-236-466-11(1)
Micro Hi-Fi
Component
System
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear panel of the unit. Record the serial
number in the space provided below. Refer to them whenever you call upon your Sony
dealer regarding this product.
Model No.
Serial No.
CMT-EX200
© 2001 Sony Corporation
Table of Contents
Parts Identification
Sound Adjustment
Adjusting the sound
— DSG ............................................. 15
Adjusting the sub woofer ........................ 15
Main unit ................................................... 4
Sub Woofer ............................................... 5
Remote Control ......................................... 6
Timer
Getting Started
Falling asleep to music
Hooking up the system .............................. 7
Replacing the battery in the remote ........ 10
Setting the time ....................................... 10
— Sleep Timer ................................. 16
Waking up to music
— Daily Timer ................................. 16
CD
Optional Components
Loading a CD .......................................... 11
Hooking up the optional components ..... 17
Playing a CD
— Normal Play/Shuffle Play/
Repeat Play ....................................... 11
Additional Information
Programing CD tracks
Precautions .............................................. 18
Troubleshooting ...................................... 19
Messages ................................................. 21
Specifications .......................................... 21
— Program Play ............................... 12
Using the CD display .............................. 13
Tuner
Presetting radio stations .......................... 13
Listening to the radio
— Preset Tuning ............................... 14
3
Parts Identification
The items are arranged in alphabetical order. Refer to the pages indicated in parentheses ( ) for
details.
Main unit
Display window 0
FUNCTION 7 (11, 17)
BUTTON DESCRIPTIONS
OPEN/CLOSE Z 1 (11)
Remote sensor 9
TUNER/BAND 6 (13)
TUNING +/– 3 (13)
VOL +/– 2
m/M 3
./> 3
x 4
NX 5
?/1 8
4
Sub Woofer
CUT OFF FREQ 3 (15)
LEVEL 1 (15)
PHASE 4 (15)
Power indicator 2
5
Remote Control
1 2 3 4
ws
wa
5
6
7
w;
8
9
0
qa
ql
qk
qs
qj
qh
qg
qd
qf
BASS +/– qg (15)
CD N qk (11)
Number buttons w; (12)
OPEN/CLOSE Z 1 (11)
PC/TAPE q; (17)
PLAY MODE wa (11, 12)
REPEAT 3 (12)
BUTTON DESCRIPTIONS
CLOCK/TIMER SELECT 6
(17)
CLOCK/TIMER SET 7 (10, 16)
DISPLAY 5 (10, 13)
DSG qd (15)
ENTER 8 (10, 12, 13, 16)
FM MODE 3 (14)
FUNCTION ws (11, 17)
MEMORY 9 (13)
@/1 4
+/– qa
. qa
> qa
X qk
x qk
m ql
M ql
SLEEP 2 (16)
SURROUND qh (15)
TREBLE +/– qf (15)
TUNER BAND qj (13)
TUNING MODE wa (13)
VOL +/– qs
6
Getting Started
Hooking up the system
Perform the following procedure 1 to 7 to hook up your system using the supplied cords and
accessories.
The front cover is made of tempered glass. Please remember to handle this system carefully.
AM loop antenna
Right satellite speaker
Left satellite speaker
Rear cover
continued
7
3 Connect the satellite speakers to the
Hooking up the system (continued)
sub woofer.
Connect the speaker cords from the satellite
speakers to the SPEAKER OUTPUT
terminals on the sub woofer as shown
below.
1 Remove the rear cover.
Sub woofer
Lined
Push in on the tabs and
pull up the cover
Clear
2 Connect the sub woofer to the system.
Connect the speaker cords from the system
to the SPEAKER INPUT terminals on the
sub woofer as shown below.
Insert this portion
To the terminals
on the satellite speaker
CMT-EX200 main unit
4 Connect the AM antenna.
Set up the AM loop antenna, then connect
it.
Lined
Clear
Connect the white cord to the U terminal,
and the red cord to the other terminal.
Insert this portion
Lined
AM loop
antenna
Clear
Sub woofer
White
Red
8
5 Reinstall the rear cover.
Put the wires through the hole at the bottom
of the rear cover.
Note on the glass cover of CD player
The CD player cover is made of tempered glass.
Under normal conditions, this tempered glass is
more shock resistant and able to bear more weight
than ordinary glass. This glass, however, may
shatter if it receives a sharp blow or if it is
scratched.
To connect optional components
See “Optional Components” on page 17.
Placing the sub woofer
Since the human ear cannot detect the direction
and position where the bass sound being
reproduced by a woofer (below 150 Hz) comes
from, you can place the woofer wherever you
like in your room. To obtain a better bass
reproduction, we recommend you to place the
woofer on a solid floor where the resonance is
unlikely to occur.
6 Connect the power cords of system
and the sub woofer to the wall outlet
after you complete all the connections.
The sub woofer switches to standby mode
automatically after a certain time (Auto
Power Off).
Notes
7 To use the remote, pull out the
insulating sheet to allow power to flow
from the battery.
• Always place the woofer vertically, keeping a few
centimeters from away the wall.
• If the woofer is placed in the center of a room, the
bass could be extreamely weakened. This is due to
the influence of the standing wave of the room. If
this happened, move the woofer away from the
center of a room or eliminate the cause of the
standing wave, by placing a bookshelf on the wall,
etc.
The remote already contains a battery.
9
Replacing the battery in
the remote
Setting the time
1 Turn on the system.
2 Press CLOCK/TIMER SET on the
1 Slide out and remove the battery case.
remote.
Proceed to step 4 when you set the clock for
the first time.
3 Press . or > repeatedly to select
“CLOCK SET”, then press ENTER on
the remote.
The day indication flashes.
4 Press . or > repeatedly to set the
2 Insert a new lithium battery CR2025
day, then press ENTER on the remote.
with the + side facing up.
The hour indication flashes.
A lithium battery CR2025
5 Press . or > repeatedly to set the
hour, then press ENTER on the remote.
The minute indication flashes.
6 Press . or > repeatedly to set the
minute, then press ENTER on the
remote.
The clock starts working.
3 Slide the battery case back in.
Tip
Tip
If you made a mistake or want to change the time,
start over from step 1.
When the remote no longer operates the system,
replace the battery with a new one.
Turning off the clock display
in standby mode
Notes
• If you do not use the remote for a long period of
time, remove the battery to avoid possible damage
from battery leakage.
• Keep the lithium battery out of the reach of
children. Should the battery be swallowed,
immediately consult a doctor.
Press DISPLAY on the remote while the
system is off.
To turn on the clock display, press DISPLAY
on the remote again.
CAUTION
Notes
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommend by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
• When the Daily Timer is set, you cannot turn off the
clock display.
• The clock display will appear when you set the
Daily Timer during turning off the display.
WARNING
Battery may explode if mistreated.
Do not recharge, disassemble or dispose of in fire.
10
CD
Playing a CD
Loading a CD
— Normal Play/Shuffle Play/Repeat
Play
1 Touch OPEN/CLOSE Z (or press OPEN/
CLOSE Z on the remote) to raise the
disc tray.
This system lets you play the CD in different
play modes.
Playing time
Track number
1 Press FUNCTION repeatedly to switch
the function to CD.
2 Press PLAY MODE on the remote
repeatedly until the mode you want
appears in the display.
Select
To play
No display
(Normal Play)
All the tracks in original
order.
2 Place a CD vertically in the disc tray.
SHUF
(Shuffle Play)
All the tracks in random
order.
With the label side facing front.
When you play a CD single (8 cm
CD), use the optional adaptor.
PGM
(Program Play)
All the tracks in the order
you want them to be played
(see “Programing CD
tracks” on page 12).
3 Press NX (or CD N on the remote).
continued
3 Touch OPEN/CLOSE Z (or press OPEN/
CLOSE Z on the remote) again to lower
the disc tray.
Note
Do not touch the playing side of the CD with your
fingers, as this may damage CD or cause the CD to
load prematurely.
11
Playing a CD (continued)
Programing CD tracks
— Program Play
Other Operations
You can make a program of up to 24 tracks.
To
Do this
Stop play
Pause
Press x.
1 Press FUNCTION repeatedly to switch
the function to CD.
Press NX (or X on the remote).
Press again to resume play.
2 Press PLAY MODE on the remote
Select a track
Press . or > repeatedly until
you find the desired track.
repeatedly until “PGM” appears.
3 Press . or > repeatedly until the
Find a point in
a track
Keep pressing m or M during
play and release it at the desired
point.
desired track number appears.
Playing time of the selected track
Remove a CD
Touch OPEN/CLOSE Z (or press
OPEN/CLOSE Z on the remote).
Play repeatedly Press REPEAT on the remote
(Repeat Play)
during play until “REP” or
“REP 1” appears.
Track number
REP: For all the tracks on the CD.
REP 1*: For a single track only.
To cancel playing repeatedly, press
REPEAT on the remote until
“REP” or “REP 1” disappears.
4 Press ENTER on the remote.
The track is programed.
The total playing time of the program and
the number of the last programed track are
displayed.
* You cannot repeat only one track during Shuffle
Play and Program Play.
5 To program additional tracks, repeat
steps 3 and 4.
Tip
If you press a number button on the remote, the track
corresponding to the pressed number on the disc starts
playing (Track Direct Play).
6 Press NX (or CD N on the remote).
Other Operations
To enter track number 10 or over
on the remote
To
Do this
Cancel Program
Play
Press PLAY MODE on the
remote repeatedly until “PGM”
and “SHUF” disappear.
1 Press >10.
2 Enter the corresponding number buttons.
To enter 0, press 10/0 instead.
Clear the entire
program
Press x in stop mode.
Example:
Select the desired Press number buttons on the
To enter track number 30, press >10, then 3 and 10/0.
track using
remote instead of performing
steps 3 to 5.
number buttons
Notes
• Do not forcibly press the disc down with your
finger, as this may cause CD player trouble.
Furthermore, do not obstruct the ejecting CD. Be
sure to touch OPEN/CLOSE Z (or press OPEN/
CLOSE Z on the remote) to lower the disc tray.
• The disc tray will not operate if you touch OPEN/
CLOSE Z while wearing gloves. Touch OPEN/
CLOSE Z with bare hands or press OPEN/
CLOSE Z on the remote.
Tips
• The program you made remains after Program Play
finishes. To play the same program again, press
NX (or CD N on the remote).
• When the total playing time has exceeded
100 minutes, the time is not displayed and the total
number of programed tracks is displayed.
12
Tuner
Using the CD display
Presetting radio stations
Press DISPLAY on the remote repeatedly.
When a CD TEXT disc is loaded, you can
check the information recorded on the disc,
such as the titles. The display changes
cyclically as follows:
You can preset 20 stations for FM and 10
stations for AM.
1 Press TUNER/BAND (or TUNER BAND
on the remote) repeatedly to select
“FM” or “AM”.
During normal play
2 Press TUNING MODE on the remote
Track number and elapsed playing time on the
current track t Track number and remaining
time on the current track t Remaining time
on the CD t Track title of the current track*
t Clock
repeatedly until “AUTO” appears.
3 Press TUNING – or + (or – or + on the
remote).
The frequency indication changes and the
scanning stops when the system tunes in a
station. “TUNED” and “STEREO” (for a
stereo program) appear.
In stop mode
Total number of tracks and total playing time
t CD disc title* t Artist name* t Clock
4 Press MEMORY on the remote.
* If a CD that has no title is loaded, nothing appears.
When the CD contains more than 20 tracks, CD
TEXT is not displayed from track 21 on.
A preset number flashes.
Proceed to step 5 while the preset number is
flashing. If the system is not operated for
more than 16 seconds, the preset number
disappears and the system returns to the
status of step 2. If this happens, start over
from step 3.
5 Press . or > to select the preset
number you want.
6 Press ENTER on the remote.
The station is stored.
7 Repeat steps 1 to 6 to store other
stations.
continued
13
Presetting radio stations (continued)
Listening to the radio
To stop scanning
— Preset Tuning
Press TUNING MODE on the remote.
Preset radio stations in the tuner’s memory first
(see “Presetting radio stations” on page 13).
To tune in a station with a weak
signal
Press TUNING MODE on the remote
repeatedly in step 2. “MANUAL” appears.
Then press TUNING – or + (or – or + on the
remote) repeatedly to tune in the station
manually and continue from step 4.
1 Press TUNER/BAND (or TUNER BAND
on the remote) repeatedly to select
“FM” or “AM”.
2 Press TUNING MODE on the remote
repeatedly until “PRESET” appears.
3 Press . or > to select the desired
To change the preset number
Start over from step 1.
preset station.
To change the AM tuning interval
Listening to non-preset radio
stations
The AM tuning interval is factory-set to 9 kHz
(10 kHz in some areas). To change the AM
tuning interval, tune in any AM station first,
then turn off the system. While holding
TUNING + on the system, turn the system back
on. When you change the interval, all the AM
preset stations are erased. To reset the interval,
repeat the same procedure.
• Press TUNING MODE on the remote
repeatedly in step 2. “MANUAL” appears.
Then press TUNING – or + (or – or + on the
remote) repeatedly to tune in the desired
station (Manual Tuning).
• Press TUNING MODE on the remote
repeatedly until “AUTO” appears in step 2
then press TUNING – or + (or – or + on the
remote). The frequency indication changes
and the scanning stops when the system
tunes in a station (Automatic Tuning).
Tips
• The preset stations are retained for about a week
even if you disconnect the power cord or if a power
failure occurs.
• When a new station is memorized, the station
formerly memorized at that preset number is erased.
To cancel Automatic Tuning
Press TUNING MODE on the remote.
Tips
• If noise is heard while listening to an FM station,
remove the FM antenna from the rear panel and
place the antenna outside the cabinet.
• To improve broadcast reception, adjust the supplied
antennas, or connect a commercially available
external antenna.
• When an FM stereo program has static noise, press
FM MODE on the remote repeatedly until
“MONO” appears. There will be no stereo effect,
but the reception will improve.
14
Sound Adjustment
Adjusting the sub woofer
Adjusting the sound
You can adjust the sound of the sub woofer to
suit the sound source and adjustment on the
system.
Generating a more dynamic
sound
1 Start playing the sound source.
— DSG
Male vocal tunes and voice containing bass
sounds are most suitable for adjustment. The
volume for the system should be set to the
same level as usual.
You can use the DSG (Dynamic Sound
Generator) function to produce a more powerful
sound.
2 Turn CUT OFF FREQ on the sub woofer to
adjust the cut-off frequency.
Press DSG on the remote.
Each time you press the button, the display
changes cyclically as follows:
3 Turn LEVEL on the sub woofer to adjust
the volume level of the sub woofer.
DSG 1 t DSG 2 t DSG OFF
When DSG is on, “DSG” lights up.
4 Press PHASE on the sub woofer
repeatedly to select the phase polarity.
The polarity changes as follows:
NORMAL (normal) y REVERSE
(reverse)
Press DSG on the remote repeatedly to cancel
DSG.
Selecting the surround effect
5 Repeat step 2 to 4 to adjust for your
Press SURROUND on the remote.
“SURR” appears in the display.
Press again to cancel surround effect.
preference.
Tips
• The power indicator lights red in standby mode.
During playing, the indicator turns green. The sub
woofer switches to standby mode automatically a
few minutes after the music ends and sound is no
longer produced.
• If the sound distorts when you turn on the bass
reinforcement (such as DSG, Bass, etc.), turn off
the bass reinforcement and adjust the sound.
• Once you have adjusted the sub woofer to the
setting you desire, you can use VOL – or + on the
system to adjust the volume of the sub woofer
linked to the satellite speakers.
Adjusting the bass
Press BASS + or – on the remote
repeatedly to adjust the bass.
You can adjust the bass in 7 steps (from –3 to
+3).
Adjusting the treble
• Reversing the polarity with PHASE on the sub
woofer may provide better bass reproduction in
certain listening environments (depending on the
position of the sub woofer/satellite and adjustment
of the cut-off frequency). It may also change the
expanse and tightness of the sound, and effect the
feeling of the sound field.
Press TREBLE + or – on the remote
repeatedly to adjust the treble.
You can adjust the treble in 7 steps (from –3 to
+3).
Tips
• You can enjoy the original sound by setting BASS
and TREBLE to 0.
Note
Never set the system’s tone control (Bass, Treble) or
DSG output to a high level or input sinewaves of
20 Hz to 50 Hz recorded on a commercially available
test disc or special sound (bass sound of electronic
musical instrument, pop noise of analog disc
turntable, sound with abnormally enhanced bass, etc.)
in a high level to this system. These actions may
cause damage to the speakers. When a special disc
containing abnormally enhanced bass is played, noise
may be output. In such a case, decrease the sound
level.
• You cannot activate DSG and Bass/Treble
adjustment at the same time.
15
Timer
Waking up to music
Falling asleep to music
— Daily Timer
— Sleep Timer
You can wake up to music at a preset time.
Make sure you have set the clock (see “Setting
the time” on page 10).
You can set the system to turn off after a
certain time, so that you can fall asleep to
music.
1 Prepare the sound source you want to
Press SLEEP on the remote to select a
desired time.
play.
• CD: Place a CD. To start from a
specific track, make a program (see
“Programing CD tracks” on page 12).
Each time you press the button, the minute
display (the turn-off time) changes cyclically as
follows:
• Radio: Tune in a station (see
“Listening to the radio” on page 14).
AUTO* t 90MIN t 80MIN t 70MIN t
…
t 10MIN t OFF
• Tape: Make the same setting on the
timer of the component connected to the
PC/TAPE jacks.
* The system automatically turns off after the current
CD finishes playing (up to 100 minutes).
When the function is TUNER, the system turns off
in 100 minutes.
2 Press VOL – or + to adjust the volume.
3 Press CLOCK/TIMER SET on the
Other Operations
remote.
To
Press
4 Press . or > repeatedly until
“TIMER SET” appears, then press
ENTER on the remote.
Check the
remaining time
SLEEP on the remote once.
Change the time SLEEP on the remote repeatedly to
to turn off select the time you want.
Cancel the Sleep SLEEP on the remote repeatedly
The hour indication flashes.
5 Set the time to start playing.
Press . or > repeatedly to set the
hour, then press ENTER on the remote.
Timer function
until “OFF” appears.
The minute indication flashes.
Note
Press . or > repeatedly to set the
When the Sleep Timer is used, you cannot use the
minute, then press ENTER on the remote.
Daily Timer.
The hour indication flashes again.
6 Set the time to stop playing following
the procedure in step 5.
The sound source indication flashes.
16
Optional Components
7 Press . or > repeatedly to select
the desired sound source.
Hooking up the optional
components
The indication changes as follows:
You can connect a digital or an analog
component to this system.
* Select “PC/TAPE” to use an optional
component connected to the PC/TAPE jacks as
the sound source.
To connect optional components, remove the
small rear cover first.
8 Press ENTER on the remote.
The start time, the stop time, and the sound
source appear in turn, before the original
display returns. “DAILY” lights up.
To the audio input
jacks of an optional
component
To the audio output
jacks of an optional
component
9 Press ?/1 to turn off the system.
Other Operations
To
Do this
Check the setting
Press CLOCK/TIMER
SELECT on the remote
repeatedly until “DAILY”
appears. The start time,
followed by the stop time, the
sound source appears, then
original display appears.
Change the setting
Cancel the timer
Start over from step 1.
Press CLOCK/TIMER
SELECT on the remote
repeatedly until “TIMER
OFF” appears.
PHONES jack
To the digital input jack
of a digital component
To
Do this
Make a digital
recording to a
digital component
Connect a optical cable.
Notes
• If the system is on about 30 seconds before the
preset time, the Daily Timer will not be activated.
• Do not operate the system from the time the system
turns on until the play starts (about 30 seconds
before the preset time).
Make an analog
recording to an
analog component
Connect the audio cords.
Listen to the
Press FUNCTION repeatedly
• Once you set the Daily Timer, it functions every
day until you cancel it.
connected optional until “PC/TAPE” appears (or
component
press PC/TAPE on the remote).
Listen through the
headphones
Connect the headphones to the
PHONES jack.
17
Additional Information
On installing
When you move the system, remove the CD.
Precautions
On operation
If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens inside the CD
player. Should this occur, the system will not operate
properly. Remove the CD and leave the system turned
on for about an hour until the moisture evaporates.
The nameplate is located on the bottom
exterior.
On safety
• The glass over the display window on the cover is
made of tempered glass.
Under normal conditions, this tempered glass is
more shock resistant and able to bear more weight
than ordinary glass. This glass, however, may
shatter if it receives a sharp blow or if it is
scratched.
• The system is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the system itself has been turned off.
• Unplug the system from the wall outlet if it is not to
be used for an extended period of time.
If you have any questions or problems concerning
your system, please consult your nearest Sony dealer.
On the speaker system
This speaker system is magnetically shielded and can
be used near TV sets. However, the picture on certain
TV sets may become magnetically distorted. In such a
case, turn off the power of the TV set once, and after
15 to 30 minutes turn it on again.
If there seems to be no improvement, locate the
speaker system further away from the TV set. Also,
be sure not to place objects in which magnets are
attached or used near the TV set, such as audio racks,
TV stands and toys. These may cause magnetic
distortion to the picture due to their interaction with
the system.
To disconnect the power cord, pull it out by the
plug. Never pull the cord itself.
• Should any solid object or liquid fall into the
system, unplug the system and have it checked by
qualified personnel before operating it any further.
• AC power cord must be changed only at the
qualified service shop.
• When you connect the power cord to a wall outlet,
even if the power is off, the system begins charging
for remote and timer functions. Therefore the
surface of this unit become warm, this is normal.
Notes on CDs
• Before playing, clean the CD with a cleaning cloth.
Wipe the CD from the center out.
• Do not use a CD with tape, seals, or paste on it as
this may damage the player.
On placement
• Place the system in a location with adequate air
circulation, and do not place anything on top of the
system.
• Do not place the system in an inclined position.
• Do not place the system in locations where it is:
— Extremely hot or cold
• Do not use solvents.
• Do not expose the CD to direct sunlight or heat
sources.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this system. Attempting to
do so may damage the system. Do not use such
discs.
— Dusty or dirty
— Very humid
— Subject to vibrations
— Subject to direct sunlight.
Cleaning the cabinet
Use a soft cloth slightly moistened with mild
detergent solution.
To avoid damaging the sub woofer
• Be careful in setting the volume control to avoid an
excessive input power.
• Do not attempt to open the enclosuer or remold
speaker units and networks.
On heat build up
—Although the system heats up during operation,
this is not a malfunction.
—Place the system in a location with adequate
ventilation to prevent heat build up in the system.
If you continuously use this system at a large volume,
the cabinet temperature of the top, side and bottom
rises considerably. To avoid burning yourself, do not
touch the cabinet.
To prevent a malfunction, do not cover the ventilation
hole for the cooling fan.
18
The remote does not function.
• Remove the obstacle.
Troubleshooting
• Move the remote closer to the system.
• Point the remote at the system’s sensor.
• Replace the battery.
If you have any problem using this system, use
the following checklist.
First, check that the power cord is connected
firmly and that the speakers are connected
correctly and firmly.
• Locate the system away from the fluorescent
light.
Should any problem persist, consult your
nearest Sony dealer.
CD Player
General
The CD tray does not lower.
• Place the CD vertically in the tray.
There is no sound.
• Always lower the tray by touching OPEN/
CLOSE Z or pressing OPEN/CLOSE Z on the
remote.
• Press VOL +.
• Make sure the headphones are not connected.
• Check the speaker connections (see page 8).
The CD does not eject.
Sound comes from one channel, or unbalanced
left and right volume.
• Consult your nearest Sony dealer.
Play does not start.
• Connect the speaker cords properly (see page 8).
• Wipe the CD clean (see page 18).
• Replace the CD.
• Place the speakers as symmetrically as possible.
• Connect only one of the supplied speakers to
• Place the CD vertically in the tray.
• Place the CD in the tray with the label side front.
each set of speaker terminals.
• Connect the supplied speakers.
• Remove the CD and wipe away the moisture on
the CD, then leave the system turned on for a
few hours until the moisture evaporates.
There is severe hum or noise.
• Move the system away from the source of noise
such as TV, VCR, etc.
• Press NX (or CD N on the remote) to start
play.
• Connect the system to a different wall outlet.
• Install a noise filter (commercially available) to
the power line.
The sound skips.
• Wipe the CD clean (see page 18).
• Replace the CD.
“12:00 AM” flashes in the display.
• Set the clock again (see page 10).
• Try moving the system to a place without
vibration (e.g., on top of a stable stand).
The timer cannot be set.
• Try moving the speakers away from the system,
• Set the clock again (see page 10).
or placing them on separate stands.
The timer does not function.
• When you listen to a track with bass sounds at
high volume, the speaker vibration may cause the
sound to skip.
• Press CLOCK/TIMER SELECT on the remote to
set the timer and light up “DAILY” in the
display (see page 17).
Play does not start from the first track.
• Check the set contents and set the correct time
• Press PLAY MODE on the remote repeatedly
until “PGM” and “SHUF” disappear to return to
normal play.
(see page 17).
• Cancel the Sleep Timer function (see page 16).
continued
19
Troubleshooting (continued)
Tuner
Severe hum or noise/stations cannot be
received.
Sub woofer and satellite speakers
• Set the proper band and frequency (see page 13).
There is no sound.
• Connect the antenna properly (see page 8).
• Connect the component properly (see page 8)
while checking:
• Find a place and an orientation that provide good
reception, then set up the antenna again. If you
cannot obtain good reception, we recommend
you connect a commercially available external
antenna.
– if the cords are connected properly.
– if the cord plugs are firmly inserted all the way.
• Turn LEVEL on the sub woofer clockwise.
• Locate the antennas as far away from the speaker
cords as possible.
The sound has suddenly stopped.
• Connect the speaker cords properly (see page 8).
• Consult your nearest Sony dealer if the supplied
AM antenna has come off the plastic stand.
The sound is distorted.
• Try turning off surrounding electrical
equipments.
• Connect the speaker cords properly (see page 8).
• Press VOL – on the system.
• Remove the FM antenna from the rear panel and
place the antenna outside the cabinet. Adjust the
antenna.
• Turn LEVEL on the sub woofer
counterclockwise.
• Turn CUT OFF FREQ on the sub woofer to
adjust cut-off frequency.
A stereo FM program cannot be received in
stereo.
Howling occurs.
• Press FM MODE until “STEREO” appears in the
display.
• Relocate the sub woofer or press VOL – on the
system.
• See “Severe hum or noise/stations cannot be
received.”, and check the antenna condition.
Severe hum or noise is heard.
• Connect the speaker cords properly (see page 8).
• The system is picking up some noise from a TV
set. Move the system away from the TV set or
turn the TV set off.
If the system still does not operate
properly after performing the above
measures, reset the system as
follows:
Optional components
1 Unplug the power cord.
There is no sound.
2 Hold down ?/1, then plug the power cord
into the wall outlet again.
• Refer to General item “There is no sound.” on
page 19 and check the condition of the system.
The system is reset to the factory settings. All
the settings you made such as the preset
stations, clock, and timer are cleared and must
be set again.
• Connect the component properly (see page 17)
while checking:
– if the cords are connected properly.
– if the cord plugs are firmly inserted all the way.
• Turn on the connected component.
• Refer to the operating instructions included with
the connected component and start playing.
The sound is distorted.
• Set the volume of the connected component
lower.
20
Messages
Specifications
One of the following messages may appear or
flash in the display during operation.
Main Unit (HCD-EX200)
Amplifier section
CD
NO DISC
For the U.S. model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
There is no CD.
OVER
With 4 ohms loads, both channels driven, from
120 – 10,000 Hz; rated 12 watts per channel
minimum RMS power, with no more than 10% total
harmonic distortion from 250 milli watts to rated
output.
You have reached the end of the CD while
pressing M during play or pause.
STEP FULL
You tried to program 25 or more tracks (steps).
Canadian model:
Continuous RMS power output (Reference):
15 + 15 watts
(4 ohms at 1 kHz,
10% THD)
Inputs
PC/TAPE IN:
voltage 250 mV,
impedance 47 kilohms
Outputs
PC/TAPE OUT:
voltage 250 mV,
impedance 1 kilohms
Optical
CD DIGITAL OUT:
PHONES (stereo mini jack):
accepts headphones of
8 ohms or more
CD player section
System
Compact disc and digital
audio system
Laser
Semiconductor laser
(λ=780 nm)
Emission duration:
continuous
Frequency response
20 Hz – 20,000 Hz
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz
(100 kHz step)
FM wire antenna
75 ohms unbalanced
10.7 MHz
Antenna
Antenna terminals
Intermediate frequency
continued
21
Sub woofer (SA-WEX200)
Amplifier section
Specifications (continued)
AM tuner section
Tuning range
For the U.S. model
530 – 1,710 kHz
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 4 ohms loads, from 50 – 150 Hz; rated 30 watts
per channel minimum RMS power, with no more than
10% total harmonic distortion from 250 milli watts to
rated output.
(with the interval set at
10 kHz)
531 – 1,710 kHz
(with the interval set at
9 kHz)
AM loop antenna
External antenna terminals
450 kHz
Antenna
Intermediate frequency
Canadian model:
Continuous RMS power output (reference):
Satellite speaker (SS-CEX200)
30 watts
(4 ohms at 55 Hz, 10%
THD)
Speaker system
Speaker units
Woofer:
Tweeter:
Impedance
Dimensions
2-way, bass-reflex type
9 cm dia., cone type
5 cm dia., cone type
4 ohms
130 × 220 × 183 mm
(w/h/d, incl. projecting
parts and controls)
Approx 2.0 kg net per
speaker
Speaker system
Speaker unit
Active sub woofer
(magnetically shielded
design)
10 cm dia, cone type
woofer (×2)
Mass
Practical maximum output 30 watts
Reproduction frequency range
45 – 150 Hz
High frequency cut-off range
70 – 150 Hz
General
Power requirements
Power consumption
120 V AC, 60 Hz
40 watts
1.8 watts (in standby
mode)
175 × 222 × 201 mm
(w/h/d, incl. projecting
parts and controls)
Approx. 3.2 kg
Remote commander with
battery (1)
Phase selector
Input
Normal, reverse
SPEAKER INPUT:
Input terminal
Output
SPEAKER OUTPUT:
Output terminal
120 V AC, 60 Hz
40 watts
Approx. 150 × 220 ×
345 mm (w/h/d, incl.
projecting parts and
controls)
Dimensions
Power requirements
Power consumption
Dimensions
Mass
Supplied accessories
AM loop antenna (1)
FM wire antenna (1)
Speaker cords (4)
Mass
Approx. 6.2 kg
Design and specifications are subject to change
without notice.
22
Sony Corporation
Printed in China
|