Installation and Assembly:
Wall Mount for SMARTboard SB685/SB690
Model: IWB600-WB
Max Load Capacity: 50 lb (22.6 kg)
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
1 of 7
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
NOTE: Make sure flange of wall bracket is located on top as shown in detail 1
Be sure wall bracket (A) is level and in desired position. Then use wall bracket (A) as a template to mark center
of four mounting holes. Drill four mounting holes. Attach wall bracket (A) to mounting surface using four screws
provided by installer and four 1/4 washers (J) if required. Once secure, wall bracket (A) will be flush with the top of
the vertical bracket (D).
1
Fasten two M4 x 6 mm phillips screws (G) into ends of wall bracket (A) as shown in Detail 1.
NOTE: Vertical brackets (D) may be used to determine location of wall bracket (A).
A
A TOP
Flange
G
Detail 1
Screws provided by installer
J
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
3 of 7
Secure Vertical brackets (D) to wall bracket (A) using two #10-32 x 3/8 thumb screws (H) and #10 flat washers
(F).
2
F
H
Detail 2
D
Secure SMARTboard channel to upper cross support (B) using eight M5 x 20 mm phillips screws (N) and eight
M5 nylock nuts (L).
NOTE: Make sure to skip attachment point as shown below.
3
B
Skip attachment point
L
SMARTboard
channel
Skip attachment point
N
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
4 of 7
Secure upper cross support (B) to vertical supports (D) using four M4 x 8 mm phillips screws (M), and
M4 nylock nuts (K).
4
D
K
B
B
M
Detail 3
M
Hook SMARTboard into SMARTboard channel on upper cross support (B).
5
SMARTboard
channel
B
SMARTboard
SMARTboard
channel
Detail 4
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
5 of 7
Fasten two support brackets (C) to vertical supports (D) using four #10-32 x 3/8 thumb screws (H).
Slide support brackets (C) up until bottom of SMARTboard rests on support as shown in detail 5.
Tighten four #10-32 x 3/8 thumb screws (H).
6
H
H
C
D
Detail 5
C
Fasten knob (I) through outside hole in support bracket (C) to determine rubber bumper (E) placement.
Secure rubber bumper (E) to board.
Repeat on opposite side of board.
7
E
C
I
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
6 of 7
Secure bottom of vertical supports (D) to mounting surface using two screws provided by installer,
and 1/4 washers (J) if required.
8
NOTE: Make sure mounting surface is suitable to hold the weight of the mount and smart board.
Screws provided by
installer
J
D
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
7 of 7
© 2010, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
|
Pelco Security Camera SS3512 User Manual
Philips Carrying Case SJM3202 User Manual
Philips Flat Panel Television 1346 User Manual
Philips Paint Sprayer 32PT81S1 User Manual
Philips Portable DVD Player DVP642K User Manual
Pioneer Car Stereo System DEH 434R User Manual
Pioneer Car Video System V7300D User Manual
Plantronics Video Game Headset CA12CD S User Manual
Porter Cable Trimmer 6603 User Manual
Poulan Trimmer PP125 User Manual