Liebherr Oven liebherr User Manual

 
Setting up  
Appliance dimensions  
• Avoidpositioningtheapplianceindirectsunlightornearcookers,  
radiators and similar sources of heat.  
• The floor on which the appliance stands should be horizontal  
and level.  
• The ventilation grilles should not be obstructed. Always ensure  
that there is good ventilation and that the outward flowing air is  
able to escape.  
• Standard EN 378 specifies that the room in which you install  
your appliance must have a volume of 1 m³ per 8 g of R 600a  
refrigerant used in the appliance, so as to avoid the formation of  
inflammable gas/air mixtures in the room where the appliance  
is located in the event of a leak in the refrigerant circuit. The  
quantity of refrigerant used in your appliance is indicated on the  
type plate on the inside of the appliance.  
A = 76 mm  
B = 2027 mm  
C = 910 mm  
D = 76 mm  
E = 910 mm  
G = 1078 mm  
H = 943 mm  
Electrical connection  
Only operate the appliance with alternating current (AC).  
The permissible voltage and frequency are indicated on the type  
plate. The position of the type plate is shown in the description of  
the appliance.  
The socket must be properly earthed and protected by a fuse.  
The tripping current of the fuse must be between 10 A and 16 A.  
The socket must not be situated behind the appliance and must  
be easily accessible.  
Do not connect the appliance using an exten-  
sion cable or extension socket.  
Appliance venting  
The required air flow is directed through the plinth.  
It is important to use the provided ventilation grille for the ventila-  
tion opening.  
This opening must not be covered.  
12  
 
GB  
Installation dimensions  
The socket must be positioned within the areas marked in grey or  
above the installation recess.  
The ice maker is fitted in the freezer compartment of the combined  
refrigerator-freezer. It must be connected to the mains water sup-  
ply to work.  
The water shut-off valve must be positioned within the areas  
marked in grey.  
WARNING!  
The water shut-off valve must not sit directly above the  
socket!  
Thegapbetweenthewatershut-ovalveandthesocket  
mustcomplywiththeregulationsofthecountryinwhich  
the appliance is used!  
13  
 
Mounting the anti-tipping device  
WARNING!  
Connection to the water supply  
Safety instructions and warnings  
• Donotconnecttothewatersupplywhilethecombinedrefrigerator-  
freezer is connected to the electricity supply.  
The supplied anti-tipping bracket must be installed in all  
cases. This prevents the appliance from tipping over when  
the fully loaded door is opened.  
The connection to the mains water supply may only be  
made by trained personnel.  
Installation:  
The water quality must comply with the drinking water  
1. Mark the centre line of the appliance on the floor.  
directives of the country in which the appliance is used.  
Align the anti-tipping bracket centre to the centre line.  
• The ice maker is designed exclusively to make ice cubes in  
quantities required by a household and may only be operated  
with water suitable for this purpose.  
CAUTION!  
• All repairs and work on the ice maker may only be carried out by  
Ensure that there are no electric cables or water pipes in the  
wallsectiontowhichtheanti-tippingbracketistobesecured.  
These could be damaged during installation.  
customer service personnel or other trained personnel.  
Themanufacturercannotacceptliabilityfordamagecaused  
by a faulty connection to the mains water supply.  
2. Secure the anti-tipping bracket to the floor using the 3 screws  
(6 mm x 60 mm) included in the accessory pack.  
The distance between the leading edge of the body of the unit  
and the rear edge of the anti-tipping bracket is 610 mm.  
Water pressure  
The water pressure must be between 0.15 and 0.6 MPa (1.5 -  
Important!  
6 bar).  
When securing the anti-tipping bracket to a concrete floor,  
use suitable plugs!  
Important:  
If the water filter is inserted in the appliance, the water  
pressure must lie between 0.3 and 0.6 MPa (3 - 6 bar).  
If the water pressure with the inserted water filter is too low,  
this may cause the ice maker to malfunction.  
If the floor slopes down sideways, the anti-tipping  
bracket must be fitted horizontally. Lay down spacers  
in the appropriate positions.  
The water supply to the appliance must be through a cold  
water pipe that can withstand  
the operating pressure and  
complies with the hygiene  
regulations. For this, use the  
stainless steel hose supplied  
(length 3 m).  
Wall  
Installation  
1. Place the appliance in front of the instal-  
lation recess.  
2. Applycoverstripsontheside  
walls of the appliance.  
14  
 
GB  
3. Insert the bent section of the hose through  
the opening at the rear of the appliance.  
7. Push the appliance slowly into the recess until the compressor  
mounting plate touches the anti-tipping bracket.  
WARNING!  
Topreventtheappliancefromtippingforwards,thecompres-  
sormountingplatemustbetouchingtheanti-tippingbracket!  
Wall  
Appliance  
4. Connect the hose to the solenoid valve  
at the front side of the appliance.  
Anti-tipping bracket  
Compressor mounting  
plate  
5. Route the mains cable towards the socket.  
6. Route the water hose towards the water shut-off valve.  
8. Connect the hose to the shut-off tap.  
Open the shut-off tap and check the system for leakage.  
WARNING!  
Important!  
Do not connect the appliance to the power supply until the  
installation is completed.  
After the ice maker has been switched on, the water supply system  
must be bled. See the section Bleeding the ice maker in the  
operating instructions.  
CAUTION!  
Lay the mains cable and the water hose in such a way that  
they will not be damaged when the appliance is slid into  
the installation recess.  
5.  
6.  
15  
 
Levelling the appliance  
Fasten the appliance in the recess  
Fasten the appliance in the recess through the upper and lower  
hinges of the refrigerator doors.  
1. Adjust the height of the  
appliance at the front by  
twisting the adjustable  
Use 2 screws for each hinge.  
1
feet  
(A/F 27). Use  
the open-ended spanner  
provided.  
Caution!  
The front feet of the ap-  
pliance must be firmly  
placed on the floor.  
screws  
(4 x 16 mm)  
2. Adjusttheheightoftheappliance  
attherearbyturningtheadjusting  
2
bars  
.
Turn the adjusting bars clock-  
wiseuntilthecompressormount-  
ingplatetouchestheanti-tipping  
bracket.  
Adjusting the front of the drawer  
If required, the front of the freezer drawers can be adjusted.  
Transfer the screws shown in the illustration (on the left and right  
sides of the freezer drawer) individually to the long slots below.  
Tighten the screws in the front of the drawer once it is in the right  
position.  
Side view of the freezer drawer  
pulled out  
16  
 
GB  
Before fitting the door panels  
Panel dimensions  
Min. panel thickness = 16 mm  
Max. panel thickness = 19 mm  
1
2
Remove the cover  
and unscrew the attachment bracket  
from the refrigerator doors. These attachment brackets will be  
mounted onto the refrigerator door panels.  
Maximum panel weight  
Refrigerator panel = 27 kg  
Important!  
Freezer drawer panel = 10 kg  
The securing nuts are needed for re-mounting the pre-  
assembled door panels onto the refrigerator doors.  
3
Unscrew the attachment brackets  
from the freezer drawers.  
Theseattachmentbracketswillbemountedontothefreezerpanels.  
Important!  
The screws are needed for re-mounting the pre-assembled  
freezer panels onto the freezer drawers.  
17  
 
Mounting the attachment brackets onto the door panels  
Mark lines on the refrigerator door panels as shown in Fig. A.  
Align the dismounted brackets of the refrigerator doors to the lines on the refrigerator door panels as shown in Fig. A 1. Fasten each  
bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm.  
Fasten the brackets provided onto the freezer drawer panels using three screws (4 x 16 mm) for each bracket (Fig. A2)  
.
Refrigerator door panels  
Fig. A 1  
Freezer drawer panel  
Freezer drawer panel  
Fig. A 2  
Fig. A  
Fig. A 2  
18  
 
GB  
Mounting the refrigerator panel  
The description is for one panel only. The procedure is the same  
for both panels.  
To make it possible to fasten the refrigerator panel at the bottom  
the soft-stop cylinder must be dismantled.  
5. Stick a small screwdriver under the retaining clamp and lever  
out (fig. D).  
1. Open the refrigerator door and suspend the refrigerator panel  
on the top adjusting pins (fig. B).  
2. Screwsecuringnutsontotheadjustingpinsandslightlytighten  
(fig. B).  
fig. D  
6. Grasp the soft-stop cylinder and pull down (Fig. E).  
The soft-stop cylinder retracts in the detached state.  
fig. B  
3. Close the refrigerator door and check the height of the panel.  
4. Adjust the height of the panel if necessary. Undo the securing  
nuts and use the adjusting pins to adjust (fig. C).  
fig. E  
7. Transfertheloweredgeoftheattachmentbracketontothepanel  
using a pencil. (fig. F). Remove the panel from the refrigerator  
door.  
fig. C  
fig. F  
19  
 
8. Dismantle the lower attachment bracket from the refrigerator  
door. Align the bracket to the lines on the refrigerator door  
panel. (fig. G).  
13. Fasten the refrigerator panel using the same screws that  
held the lower bracket before removal (fig. K).  
Fasten the bracket with any hole wherever possible using a  
minimum of 6 screws 4 x 16 mm.  
fig. K  
fig. G  
14. Extend the soft-stop cylinder and connect with the ball stud  
(fig. L).  
9. Opentherefrigeratordoorandsuspendtherefrigeratorpanel  
on the top adjusting pins (fig. H).  
10. Screwsecuringnutsontotheadjustingpinsandslightlytighten  
(fig. H).  
fig. L  
15. Attach the retaining clamp to the ball housing of the soft-stop  
cylinder (fig. M).  
fig. H  
11. Move the panel to the left until it makes contact with the center  
rail (fig. I).  
12. Tighten the hex nuts finally.  
fig. M  
fig. I  
20  
 
GB  
16. Click cover into place (fig. N).  
Mounting the dust filter  
Thesupplieddustfilterpreventsthatdirtentersthemotorcompart-  
ment, reducing the refrigeration performance. Therefore always  
install the dust filter.  
1. Pull the bottom freezer drawer right out.  
2. Remove the protective film from the dust filter. Insert the filter at  
the bottom, press the button down and click the filter into place.  
fig. N  
Mounting the freezer panels  
1. Pulloutthetopfreezerdrawerandscrewonthepre-assembled  
panel. The same screws must be used as those used to screw  
on the attachment brackets (3.5 x 13).  
Mounting the ventilation grille  
Important!  
To ensure fault-free operation of the appliance, you must  
install the supplied ventilation grille.  
2. Close the freezer drawer and check the position of the panel.  
Adjust the height of the panel by undoing the left and right  
screws. Tighten the screws.  
Donotobstructtheventilationopeningorcoveritwithapanel!  
3. Pull out the bottom freezer drawer and mount the panel in the  
same way.  
4. For both drawers, cover the gap between the drawer and the  
panel with the cover strips supplied. Remove the protective  
film from the trim and insert into the gap at the top.  
3.5 x 13 mm  
21  
 

LG Electronics CRT Television 32LP645H User Manual
LOREX Technology Security Camera SG21CD7444UQ A80 User Manual
LST Smoke Alarm AISA 45681 321 User Manual
Lucent Technologies Marine Radio 1021OX User Manual
Magnavox Cassette Player AZ8289 User Manual
Manitowoc Ice Indoor Furnishings 7623123 User Manual
Maytag Range MER67 User Manual
McIntosh Portable Speaker XCS2K User Manual
Micro Innovations Digital Camera Micro Webcam Matrix User Manual
Midland Radio Marine Radio 70 440BP User Manual